manualshive.com logo in svg

Hafco Woodmaster OS-140, Руководство по эксплуатации

Поделиться
Скачать
Hafco Woodmaster OS-140 Скачать руководство пользователя страница 9

9

OPERATION MANUAL

3. SETUP

3.1 UNPACKING AND CLEAN-UP

 

1.  Carefully remove all contents from the shipping carton.  Compare the contents with those   

 

listed on Page 4. Make sure that all of the items are accounted for, before discarding any    

 

packing material. Place parts on a protected surface for easy identification and assembly. If  

 

any parts are missing or broken, please contact your distributor for replacements. DO  

 

 

NOT turn your machine ON if any of these items are missing. You may cause personal injury  

 

or damage to the machine.

2.  Report any shipping damage to your local distributor.

3.  Clean all rust protected surfaces with ordinary house hold type grease or spot remover.  Do  

 

not use; gasoline, paint thinner, mineral spirits, etc. These may damage painted surfaces.

4.  Apply a coat of paste wax to the table to prevent rust. Wipe all parts thoroughly with a  

 

 

clean dry cloth.

5.  Set packing material and shipping carton aside. Do not discard until the machine has been  

 

set up and is running properly.

3.2 ATTACHING THE RUBBER FEET

1.   DISCONNECT THE MACHINE FROM THE POWER

2.   Lower the machine onto its side to access the four holes in  

 

the bottom corners of the base.

3.   Insert the threaded portion of the rubber foot through the  

 

machine’s base, and put on a washer, followed by a nut to  

 

secure the foot in place. (Fig.3.1)

4.   Install the remaining three rubber feet and then raise the  

 

machine to its operating position. The rubber feet will   

 

prevent the machine from slipping on the bench during  

 

use, and reduce any vibration from the sanding operation.  

F

ig

.3.1

3.3 POSITIONING THE OSCILLATING SPINDLE SANDER.

When selecting the position for the machine, consider the largest size of workpiece that will 

be processed on the machine and provide enough space around the machine for operating 

the machine safely. Consideration should be given to the installation of auxiliary equipment, 

and room for any maintenance that may need to be carried out. The Oscillating Spindle Sander 

must be positioned where it is to be used on a sturdy workbench, at a suitable, safe height for 

the sanding operations to be carried out. 

THE MACHINE MUST HAVE THE POWER PLUG REMOVED FROM THE SOCKET BEFORE ANY 

ADJUSTMENTS ARE ATTEMPTED AND REMAIN UNPLUGGED UNTIL COMPLETED.

Page 9

Instruction Manual for OS-140 (W792)

20/02/2019

Содержание OS-140


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды