background image

 

 

 

 

5.52.208.00.01.06 

 

 

 

9

 

Safety check .................................................................................... 13

 

10

 

Functional test ................................................................................. 13

 

11

 

Maintenance .................................................................................... 13

 

11.1

 

General ........................................................................................................................... 13

 

11.2

 

Monitoring ...................................................................................................................... 13

 

12

 

Inspection ........................................................................................ 13

 

12.1

 

Periodic checks ............................................................................................................. 13

 

12.2

 

Wire rope ........................................................................................................................ 13

 

12.3

 

Inspection intervals ....................................................................................................... 14

 

13

 

Service ............................................................................................. 14

 

13.1

 

Wire rope ........................................................................................................................ 14

 

13.2

 

Gear ................................................................................................................................ 14

 

13.3

 

Gear spring pressure brake .......................................................................................... 14

 

13.4

 

Lubricant - Selection ..................................................................................................... 14

 

13.5

 

Lubricant for food industry – Selection (as option*) ................................................... 15

 

14

 

Trouble ............................................................................................. 15

 

15

 

Remedy ............................................................................................ 15

 

16

 

Decommissioning ........................................................................... 15

 

16.1

 

Temporary decommissioning ....................................................................................... 15

 

16.2

 

Final decommissioning/disposal .................................................................................. 15

 

 

 

 

Information 

 

 

The products meet European Union requirements, in particular the valided EU Machine Directive. 

The entire company works acc. to a certified quality assurance system as per ISO 9001. 

The production of components at our work is subject to strict, intermediate checks. 

After assembly, each product is subject to a final test with overload. 

For the operation of hoists, the national accident prevention regulations apply in Germany, amongst others. 

The stated performance of the devices and meeting any warranty claims require adherence to all instructions 
in this manual. 

Before delivery, all products are packed properly. Check the goods after receipt for any damage caused 
during transport. Report any damage immediately to the forwarding agent. 

This manual allows a safe and efficiently use of equipment. Images of this manual are for a principle 
understanding and can be different from the real design. 

 

NOTICE!

 

We refer to the prescribed equipment tests before initial start-up, before putting back into operation and the 
regular periodic inspections. 

In other countries any additional national regulations must be observed. 

 

 

 

 

Содержание 238/10
















Отзывы: