manualshive.com logo in svg

Hach PHC705A, Руководство пользователя

Поделиться
Скачать
Hach PHC705A Скачать руководство пользователя страница 5

Section 1 Product overview

The Intellical PHC705A pH probes are digital, combination electrodes that measure the pH of water
samples. The probes have a special pH glass bulb material to help decrease sodium interference in
very alkaline water samples (pH values higher than 12). The probes use the Red Rod technology
and a saturated KCl electrolyte for high performance. The probes are refillable and have a built-in
temperature sensor. A 59-mL bottle of reference electrolyte filling solution (saturated KCl solution) is
supplied with the probe. Refer to 

Figure 1

.

Note: Do not use the probe to measure the pH of organic solvents, emulsions or samples with many solids.

Figure 1  Probe overview

1   

Probe soaker bottle with storage solution

5   

Probe soaker bottle holder

2   

Filling-hole plug

6   

Electrode filling and storage solution

3   

Protective tape and filling hole

7   

Reference junction

4   

Cable

8   

Glass bulb and temperature sensor

Section 2 Specifications

Specifications are subject to change without notice.

Specifications

Details

Probe type

Digital combination glass pH probe with refillable electrolyte and built-
in temperature sensor

pH range

0 to 14 pH

pH accuracy

±0.01 pH

Reference type

Red Rod (Ag/AgCl in protective tubes)

Reference junction

Porous pin

Slope

–59 mV/pH (85 to 115% at 25 °C (77 °F) per Nernstian theoretical
value)

Isopotential point

6.00 pH

English

   

3

Содержание PHC705A























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды