background image

Section 1 Product overview

The Intellical PHC281 series pH probes are digital, combination electrodes that measure the pH of
water samples. The probes are refillable and have a built-in temperature sensor. The probes have
good performance in low ionic strength (LIS) samples (e.g., deionized, reverse osmosis, distilled) and
other clean waters (specific conductance less than 100 µS/cm to ultrapure). The open reference
junction lets the electrolyte flow at a high rate for optimum electrical connection with the sample. The
open reference junction does not become clogged with suspended solids if used in dirty applications.
A 59-mL bottle of 2.44 M KCl reference electrolyte filling solution is supplied with the probe. Refer to 

Figure 1

.

Note: Do not use the probe for measurements in organic solvents.

Figure 1  Probe overview

1   

Probe soaker bottle with storage solution

5   

Cable

2   

Glass bulb, reference junction and
temperature sensor

6   

Probe soaker bottle holder

3   

Filling-hole plug

7   

Electrode filling and storage solution

4   

Protective tape and filling hole

8   

Dispensing cap

Section 2 Specifications

Specifications are subject to change without notice.

Specifications

Details

Probe type

Digital combination pH probe with refillable electrolyte and built-in
temperature sensor

pH range

0 to 14 pH

pH accuracy

±0.02 pH

Reference type

Ag/AgCl

Reference junction

Open

Slope

–59 mV/pH (90 to 110% at 25 °C (77 °F) per Nernstian theoretical
value)

Isopotential point

0 (±30) mV at 7.0 (±0.5) pH

Sodium (alkalinity) error

–0.6 pH at pH 12.6 in 1 M NaOH

English

   

3

Содержание PHC281





















Отзывы: