Operating instructions 36009
Welding device
PQ-18
Page 2 of
14
Edition: 03/0404
Subject to alterations
Table of contents
1.
General information ............................................................................................................................ 3
1.1
Application............................................................................................................................................. 3
1.2
Important safety terms .......................................................................................................................... 3
1.3
Scope of supply..................................................................................................................................... 4
1.3.1
Available accessories ........................................................................................................................... 4
1.4
Ordering of accessories/spare parts..................................................................................................... 5
1.5
Warranty................................................................................................................................................ 5
1.6
Technical advice ................................................................................................................................... 5
2.
Mode of operation ............................................................................................................................... 6
3.
Initial start-up ...................................................................................................................................... 6
4.
Welding of Polycord round belts....................................................................................................... 7
5.
Service.................................................................................................................................................. 8
5.1
Maintenance.......................................................................................................................................... 8
5.2
Measuring of the plate temperature ...................................................................................................... 8
5.3
Adjusting of the thermostat ................................................................................................................... 9
5.4
Replacement of the power cord ............................................................................................................ 9
6.
Illustrations........................................................................................................................................ 10
7.
Technical data ................................................................................................................................... 11
8.
Drawing and spare part numbers.................................................................................................... 12
9.
Required accessories....................................................................................................................... 13
9.1
Cutting device S-16............................................................................................................................. 13
Appendix:
Product
Liability
