H3C UniServer R4900 G5 Скачать руководство пользователя

Страница: 40 / 141

Enter the BIOS and select boot options. For more information, see "

Selecting the boot media

Select

Red Hat Enterprise Linux 7.2

, and then press

as prompted, as shown in

Figure 54

Figure 54 Confirming OS installation

Input

linux

at the end of the line that starts with

linuxefi

, and then press

F10

Ctrl+X

start installation.

Figure 55 Parameter configuration

Perform the following steps to configure the parameters:

Display the location of the driver. In this example,

sr1

has a driver mounted, so you select

Enter

to select the rpm file.

Enter

to continue installation.

If not all drivers are listed on the page, enter

to refresh the driver list.

Содержание UniServer R4900 G5














































































































































Результаты поиска

Содержание UniServer R4900 G5

Отзывы:

Похожие инструкции для UniServer R4900 G5

Бренды по названию

Популярные бренды

H3C UniServer R4900 G5, Руководство по установке операционной системы

Результаты поиска

Содержание UniServer R4900 G5

Отзывы:

Похожие инструкции для UniServer R4900 G5

Бренды по названию

Популярные бренды