H3C S5810 Series Скачать руководство пользователя страница 16

Страница: 16 / 57

1-10

LED

Description

SFP+ interface status LED

See SFP+ Interface Status LED on page 1-13.

Management Ethernet port status LED

See Management Ethernet Port Status LED on page
1-13.

System LED

Table 1-10

System LED description

LED

Status

Description

Steady green

The switch is started normally.

Flashing green (1 Hz)

The system is performing POST.

Steady red

POST failed.

Flashing yellow (1 Hz)

POST on some ports failed.

SYS

Off

The switch is powered off.

Power Module Status LEDs

Table 1-11

Description of the LEDs

Mark

Status

Steady green

Hot swappable power module slot 1 is installed with a power
module, and the power input is normal.

Steady yellow

Hot swappable power module slot 1 is installed with a power
module, but an output failure occurs.

PWR1

Off

No power module is installed in hot swappable power module
slot 1, or no power is input.

Steady green

Hot swappable power module slot 2 is installed with a power
module, and the power input is normal.

Steady yellow

Hot swappable power module slot 2 is installed with a power
module, but an output failure occurs.

PWR2

Off

No power module is installed in hot swappable power module
slot 2, or no power is input.

Seven-Segment LED

The seven-segment LED and the system LED together indicate the operating status of the device. For
details, refer to Table 1-12.

Table 1-12

Seven-segment LED description

Status

Mark

System LED

(SYS) status

Seven-segment LED status

Description

Unit

Flashing green

The LED displays the specific POST running. The LED

Содержание S5810 Series


























































Результаты поиска

Содержание S5810 Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5810 Series, Быстрый старт

Результаты поиска

Содержание S5810 Series

Отзывы:

Бренды по названию

Популярные бренды