H3C S5500-SI Series Скачать руководство пользователя

Страница: 38 / 130

3-13

Decide the remote MEP for each MEP, and enable these MEPs.

According to the network diagram as shown in

Figure 3-7

, perform the following configurations:

In MD_A, there are three edge ports: GigabitEthernet 1/0/1 on Device A, GigabitEthernet 1/0/3 on

Device D and GigabitEthernet 1/0/4 on Device E. Configure inward-facing MEPs on these ports

respectively.

In MD_B, there are two edge ports: GigabitEthernet 1/0/3 on Device B and GigabitEthernet 1/0/1

on Device D. Configure outward-facing MEPs on the two ports respectively.

In MD_A and MD_B, each MEP checks the messages from other MEPs.

Figure 3-7

Network diagram of MD and MEP configuration

Configuration procedure

1) On Device A

<DeviceA> system-view

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] cfd mep 1001 service-instance 1 inbound

[DeviceA-GigabitEthernet1/0/1] cfd remote-mep 5001 service-instance 1 mep 1001

[DeviceA-GigabitEthernet1/0/1] cfd remote-mep 4002 service-instance 1 mep 1001

[DeviceA-GigabitEthernet1/0/1] cfd mep service-instance 1 mep 1001 enable

[DeviceA-GigabitEthernet1/0/1] cfd cc service-instance 1 mep 1001 enable

2) On Device B

<DeviceB> system-view

[DeviceB] interface gigabitethernet 1/0/3

[DeviceB-GigabitEthernet1/0/3] cfd mep 2001 service-instance 2 outbound

[DeviceB-GigabitEthernet1/0/3] cfd remote-mep 4001 service-instance 2 mep 2001

[DeviceB-GigabitEthernet1/0/3] cfd mep service-instance 2 mep 2001 enable

[DeviceB-GigabitEthernet1/0/3] cfd cc service-instance 2 mep 2001 enable

3) On Device D

<DeviceD> system-view

[DeviceD] interface gigabitethernet 1/0/1

[DeviceD-GigabitEthernet1/0/1] cfd mep 4001 service-instance 2 outbound

[DeviceD-GigabitEthernet1/0/1] cfd remote-mep 2001 service-instance 2 mep 4001

[DeviceD-GigabitEthernet1/0/1] cfd mep service-instance 2 mep 4001 enable

[DeviceD-GigabitEthernet1/0/1] cfd cc service-instance 2 mep 4001 enable

[DeviceD-GigabitEthernet1/0/1] interface gigabitethernet 1/0/3

[DeviceD-GigabitEthernet1/0/3] cfd mep 4002 service-instance 1 inbound

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды