H3C S5500-SI Series Скачать руководство пользователя

Страница: 36 / 130

3-11

To do...

Use the command...

Remarks

Display the attribute and running

information of the MEPs

display cfd mep mep-id

service-instance instance-id

Available in any view

Display LTR information received

by a MEP

display cfd linktrace-reply

[

service-instance instance-id

[

mep mep-id

] ]

Available in any view

Display the information of a remote

MEP

display cfd remote-mep

service-instance instance-id mep

mep-id

Available in any view

Display the content of the LTR that

responds to LTM messages

display cfd linktrace-reply

auto-detection

[

size size-value

]

Available in any view

CFD Configuration Examples

Configuring Service Instance

Network requirements

As shown in

Figure 3-6

, there are five devices in the MDs. Each device has four ports belonging to

VLAN 100. The light blue square frame and the blue one specify two different MDs.

Two MDs, MD_A (indicated by the light blue square frame, with level 5) and MD_B (indicated by

the blue square frame, with level 3)) are designed in this network.

Define the edge ports of each MD, and define the MD of each port.

The VLAN IDs of each MA in the two MDs are all 100.

According to the network diagram as shown in

Figure 3-6

, You should perform the following

configurations:

Configure MD_A on Device A and Device E

Configure MD_B on Device C

Configure MD_A and MD_B on Device B and Device D

Configure an MA in each MD

Configure a service instance for each MA

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды