H3C S5150-EI Series Скачать руководство пользователя страница 41

Страница: 41 / 59

# Assign Ten-GigabitEthernet 1/0/1, Ten-GigabitEthernet 1/0/2, Ten-GigabitEthernet 1/0/3, and
Ten-GigabitEthernet 1/0/4 to the aggregate interface.

[Sysname] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[Sysname-if-range] port link-aggregation group 2

[Sysname-if-range] quit

BFD MAD-enabled IRF configuration example

Network requirements

As shown in

Figure 16

, set up a four-chassis IRF fabric at the distribution layer of the enterprise

network.

•

Configure BFD MAD on the IRF fabric and set up BFD MAD links between each member device
and the intermediate device.

•

Disable the spanning tree feature on the ports used for BFD MAD, because the two features
conflict with each other.

Figure 16 Network diagram

Configuration procedure

Configure Device A:

# Shut down the physical interfaces used for IRF links.

<Sysname> system-view

[Sysname] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[Sysname-if-range] shutdown

[Sysname-if-range] quit

Device A

Device B

IRF

Device C

Device D

IRF link

BFD MAD link

Data link

XGE1/0/3
XGE1/0/4
(IRF-port 1/2)

XGE2/0/1
XGE2/0/2

(IRF-port 2/1)

XGE2/0/3
XGE2/0/4
(IRF-port 2/2)

XGE4/0/1
XGE4/0/2
(IRF-port 4/1)

XGE4/0/3
XGE4/0/4

(IRF-port 4/2)

XGE3/0/1
XGE3/0/2
(IRF-port 3/1)

XGE3/0/3
XGE3/0/4

(IRF-port 3/2)

XGE1/0/1
XGE1/0/2

(IRF-port 1/1)

XGE1/0/5

XGE3/0/5

XGE4/0/5

XGE2/0/5

/0/1

XGE1/

0/4

Device E

Содержание S5150-EI Series




























































Результаты поиска

Содержание S5150-EI Series

Отзывы:

Похожие инструкции для S5150-EI Series

Бренды по названию

Популярные бренды

H3C S5150-EI Series, Руководство по настройке

Результаты поиска

Содержание S5150-EI Series

Отзывы:

Похожие инструкции для S5150-EI Series

Бренды по названию

Популярные бренды