H3C S5150-EI Series Скачать руководство пользователя страница 37

Страница: 37 / 59

Configuration examples

This section provides IRF configuration examples for IRF fabrics that use different MAD
mechanisms.

LACP MAD-enabled IRF configuration example

Network requirements

As shown in

Figure 15

, set up a four-chassis IRF fabric at the access layer of the enterprise network.

Configure LACP MAD on the multichassis aggregation to Device E, an H3C device that supports
extended LACP.

Figure 15 Network diagram

Configuration procedure

Configure Device A:

# Shut down the physical interfaces used for IRF links. In this example, the physical interfaces
are shut down in batch. For more information, see

Layer 2—LAN Switching Configuration

Guide

<Sysname> system-view

[Sysname] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[Sysname-if-range] shutdown

[Sysname-if-range] quit

# Bind Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to IRF-port 1/1.

[Sysname] irf-port 1/1

[Sysname-irf-port1/1] port group interface ten-gigabitethernet 1/0/1

XGE1/0/3
XGE1/0/4
(IRF-port1/2)

XGE2/0/1
XGE2/0/2
(IRF-port2/1)

XGE1/0/5

XGE2/0/5

Device A

Device B

XGE1/0/1-XGE1/0/4

IRF

IP network

Device E

Device C

Device D

XGE1/0/1
XGE1/0/2
(IRF-port1/1)

XGE3/0/3
XGE3/0/4
(IRF-port3/2)

XGE3/0/1
XGE3/0/2
(IRF-port3/1)

XGE4/0/3
XGE4/0/4
(IRF-port4/2)

XGE2/0/3
XGE2/0/4
(IRF-port2/2)

XGE4/0/1
XGE4/0/2
(IRF-port4/1)

XGE3/0/5

XGE4/0/5

Содержание S5150-EI Series




























































Результаты поиска

Содержание S5150-EI Series

Отзывы:

Похожие инструкции для S5150-EI Series

Бренды по названию

Популярные бренды

H3C S5150-EI Series, Руководство по настройке

Результаты поиска

Содержание S5150-EI Series

Отзывы:

Похожие инструкции для S5150-EI Series

Бренды по названию

Популярные бренды