H3C S5150-EI Series Скачать руководство пользователя страница 50

Страница: 50 / 59

Figure 18 Network diagram

Configuration procedure

Configure Device A:

# Shut down the physical interfaces used for IRF links.

<Sysname> system-view

[Sysname] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[Sysname-if-range] shutdown

[Sysname-if-range] quit

# Bind Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to IRF-port 1/1.

[Sysname] irf-port 1/1

[Sysname-irf-port1/1] port group interface ten-gigabitethernet 1/0/1

[Sysname-irf-port1/1] port group interface ten-gigabitethernet 1/0/2

[Sysname-irf-port1/1] quit

# Bind Ten-GigabitEthernet 1/0/3 and Ten-GigabitEthernet 1/0/4 to IRF-port 1/2.

[Sysname] irf-port 1/2

[Sysname-irf-port1/2] port group interface ten-gigabitethernet 1/0/3

[Sysname-irf-port1/2] port group interface ten-gigabitethernet 1/0/4

[Sysname-irf-port1/2] quit

# Bring up the physical interfaces and save the configuration.

[Sysname] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[Sysname-if-range] undo shutdown

[Sysname-if-range] quit

[Sysname] save

# Activate the IRF port configuration.

[Sysname] irf-port-configuration active

XGE1/0/3
XGE1/0/4
(IRF-port1/2)

XGE2/0/1
XGE2/0/2
(IRF-port2/1)

XGE1/0/5

XGE2/0/5

Device A

Device B

XGE1/0/1-XGE1/0/4

IRF

IP network

Device E

Device C

Device D

XGE1/0/1
XGE1/0/2
(IRF-port1/1)

XGE3/0/3
XGE3/0/4
(IRF-port3/2)

XGE3/0/1
XGE3/0/2
(IRF-port3/1)

XGE4/0/3
XGE4/0/4
(IRF-port4/2)

XGE2/0/3
XGE2/0/4
(IRF-port2/2)

XGE4/0/1
XGE4/0/2
(IRF-port4/1)

XGE3/0/5

XGE4/0/5

Содержание S5150-EI Series




























































Результаты поиска

Содержание S5150-EI Series

Отзывы:

Похожие инструкции для S5150-EI Series

Бренды по названию

Популярные бренды

H3C S5150-EI Series, Руководство по настройке

Результаты поиска

Содержание S5150-EI Series

Отзывы:

Похожие инструкции для S5150-EI Series

Бренды по названию

Популярные бренды