H3C S3610-28F Скачать руководство пользователя страница 392

Страница: 392 / 1547

Operation Manual – IPv4 Routing
H3C S3610&S5510 Series Ethernet Switches

Chapter 3 OSPF Configuration

3-24

Note:

An OSPF process ID is unique, including the process ID for OSPF multi-instance,

which cannot be the same as any previously configured ID.

A network segment can only belong to one area.

It is recommended to configure a description for each OSPF process to help identify

purposes of processes and for ease of management and memorization.

It is recommended to configure a description for each area to help identify purposes

of areas and for ease of management and memorization.

3.4 Configuring OSPF Area Parameters

Splitting an OSPF AS into multiple areas reduces the number of LSAs in the networks

and extends the OSPF application. For those non-backbone areas residing on the AS

boundary, you can configure them as stub areas to further reduce the size of routing

tables on routers in these areas and the number of LSAs.

A stub area cannot redistribute routes, and for this reason, NSSA was introduced. In

NSSA areas, Type-7 LSAs (NSSA External LSAs) can be advertised. Type 7 LSAs

originate from the ASBR in a NSSA area. When arriving at the ABR in the NSSA area,

these LSAs will be translated into type 5 LSAs for advertisement to other areas.

Non-backbone areas exchange routing information via the backbone area. Therefore,

the backbone and non-backbone areas, including the backbone itself must maintain

connectivity.

If necessary physical links are not available for this connectivity maintenance, you can

configure virtual links to solve it.

3.4.1 Prerequisites

Before configuring an OSPF area, you have configured:

IP addresses for interfaces, making neighboring nodes accessible with each other

at the network layer.

OSPF basic functions.

Содержание S3610-28F












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S3610-28F

Отзывы:

Похожие инструкции для S3610-28F

Бренды по названию

Популярные бренды

H3C S3610-28F, Руководство по эксплуатации

Результаты поиска

Содержание S3610-28F

Отзывы:

Похожие инструкции для S3610-28F

Бренды по названию

Популярные бренды