H3C S3610-28F Скачать руководство пользователя страница 328

Страница: 328 / 1547

Operation Manual – Routing Overview
H3C S3610&S5510 Series Ethernet Switches

Chapter 1 IP Routing Overview

1-1

Chapter 1 IP Routing Overview

Go to these sections for information you are interested in:

IP Routing and Routing Table

Routing Protocol Overview

Displaying and Maintaining a Routing Table

Note:

The term “router” in this document refers to a Layer 3 switch running routing

protocols.

Verify that the system already operates in IPv4/IPv6 dual-stack mode before

configuring IPv6 routing. For dual-stack mode configuration, see the part covering

dual-stack in the IPv6 Configuration module.

1.1 IP Routing and Routing Table

1.1.1 Routing

Routing in the Internet is achieved through routers. Upon receiving a packet, a router

finds an optimal route based on the destination address and forwards the packet to the

next router in the path until the packet reaches the last router, which forwards the

packet to the intended destination host.

1.1.2 Routing Through a Routing Table

I. Routing table

Routing tables play a key role in routing. Each router maintains a routing table, and

each entry in the table specifies which physical interface a packet destined for a certain

destination should go out to reach the next hop (the next router) or the directly

connected destination.

Routes in a routing table can be divided into three categories by origin:

Direct routes: Routes discovered by data link protocols, also known as interface

routes.

Static routes: Routes that are manually configured.

Dynamic routes: Routes that are discovered dynamically by routing protocols.

Содержание S3610-28F












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S3610-28F

Отзывы:

Похожие инструкции для S3610-28F

Бренды по названию

Популярные бренды

H3C S3610-28F, Руководство по эксплуатации

Результаты поиска

Содержание S3610-28F

Отзывы:

Похожие инструкции для S3610-28F

Бренды по названию

Популярные бренды