H3C S12500X-2L Скачать руководство пользователя страница 26

Страница: 26 / 27

5-2

Viewing switch startup information

After the switch is powered on, the configuration terminal output startup information. The output
information varies by software versions.

The following shows a sample output you will see when the switch starts up:

System is Starting....

Press Ctrl+D to access BASIC-BOOTWARE MENU

Press Ctrl+T to access BOOTWARE DIAG-TEST MENU

Booting Normal Extend Bootware

[Warning]Use default bootware config!

****************************************************************************

* *

* BootWare, Version 1.02 *

* *

****************************************************************************

Compiled Date : Jul 4 2019

Memory Type : DDR4 SDRAM

Memory Size : 16384MB

Memory Speed : 2133MHz

flash Size : 7296MB

CPLD 1 Version : 0.0

CPLD 2 Version : 0.0

CPLD 3 Version : 0.0

PCB Version : Ver.A

BootWare Validating...

Press Ctrl+B to access EXTENDED-BOOTWARE MENU...

Loading the main image files...

Loading file flash:/SYSTEM.bin..............................................

............................................................................

....................................Done.

Loading file flash:/BOOT.bin................................................

............................................................................

................Done.

Image file flash:/BOOT.bin is self-decompressing............................

............................................................................

.............................................Done.

System image is starting...

Line aux1/0 is available.

Press ENTER to get started.

Press

Enter

at the prompt. When the prompt

appears, you can configure the switch.

Содержание S12500X-2L




























Результаты поиска

Содержание S12500X-2L

Отзывы:

H3C S12500X-2L, Быстрый старт, Страница: 26 / 27

Результаты поиска

Содержание S12500X-2L

Отзывы: