H3C MSR Series Скачать руководство пользователя страница 10

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

reg

 

1

 command in probe view to collect the FPGA information. 

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

reg

 

2

 command in probe view to collect the MAC information. 

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

reg

 

3

 command in probe view to collect the PHY information. 

6. 

Contact H3C Support. 

Failure to forward packets 

Symptom 

An Ethernet interface on an intermediate router cannot forward packets. 

Solution 

To resolve the problem: 

1. 

Verify that the Ethernet interface can ping the directly connected device. If the ping operation 
fails, see "

Failure to ping the directly connected device

." 

2. 

Use the 

debugging ip packet

 command to verify that the interface can transmit packets 

correctly. 

3. 

Collect the following information for the interface: 

{

 

Execute the 

display hardware internal module 

interface-name interface-number

 

statistics 

command in probe view to collect the interface statistics. 

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

status 

command in probe view to collect the status information. 

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

reg

 

1

 command in probe view to collect the FPGA information. 

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

reg

 

2

 command in probe view to collect the MAC information. 

{

 

Execute the 

display hardware internal module

 

interface-name interface-number

 

reg

 

3

 command in probe view to collect the PHY information. 

4. 

Contact H3C Support. 

Packet dropping 

Symptom 

An Ethernet interface drops packets. 

Solution 

To resolve the problem: 

1. 

Determine whether the packets are dropped by the local end or the peer end by executing the 
following commands to compare the rates of the two ends: 

{

 

Execute the 

display counters rate inbound interface

 command on the local end 

to view the inbound traffic rate statistics. 

Содержание MSR Series





























Отзывы: