H3C External PoE Power System PSE2500-A3 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

H3C External PoE Power System PSE2500-A3 Скачать руководство пользователя страница 6

User Manual
PSE2500-A3 External PoE
Power System

Table of Contents

i

Table of Contents

Chapter 1 Introduction ..................................................................1-1

1.1 Architecture and Configurations.........................................1-1

1.2 Features .............................................................................1-3

Chapter 2 System Description .....................................................2-1

2.1 Overview ............................................................................2-1

2.1.1 Rectifier ...................................................................2-1

2.1.2 Rectifier Bracket ......................................................2-2

2.1.3 Rectifier Visual Displays..........................................2-2

2.2 Controller............................................................................2-3

2.3 AC Distribution Unit............................................................2-6

2.4 DC Distribution Unit............................................................2-6

Chapter 3 Safety ............................................................................3-1

3.1 Safety Statements..............................................................3-1

3.2 Warning Statements and Safety Symbols .........................3-2

3.3 Precautions ........................................................................3-3

Chapter 4 Installation and Debugging.........................................4-1

4.1 Introduction ........................................................................4-1

4.1.1 Guidelines................................................................4-1

4.1.2 EMI Considerations .................................................4-1

4.1.3 Installation Tools and Hardware..............................4-1

4.1.4 Safety ......................................................................4-2

4.1.5 Installation Sequence ..............................................4-2

4.2 Physical Mounting ..............................................................4-3

«
...
4
5
6
7
8
...
»

Содержание External PoE Power System PSE2500-A3

































Отзывы:

Нет отзывов