H3C DSIC-9FSW Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 219

background image

28

Interface LEDs

Figure 33 DSIC-4FXS1FXO panel

Table 39 LED description

LED

Description

LINK/ACT

•

Off: The link is idle.

•

Steady green: The link is being occupied for call connection.

•

Flashing yellow: The link is being occupied for communication.

Interface cables and the connection methods

For more information about FXS/FXO interface cables and the connection methods, see
"

ADSL/BS/FXS/FXO/AM/FCM interface

."

SIC-1BSV/SIC-2BSV

Introduction

The 1/2-port ISDN BRI S/T voice interface module (SIC-1BSV/SIC-2BSV) is mainly used to process
(receive/transmit and compress/decompress) the ISDN interface voice traffic. The interface(s) on the
SIC-1BSV/SIC-2BSV module is (are) ITU-T I.430-compliant, adopting pseudo-ternary coding,
providing 192 Kbps interface rate, and allowing the maximum transmission distance of 1 km (0.6
miles) in point-to-point mode. In the upstream direction, the SIC-1BSV/SIC-2BSV module can be
connected to a user interface on an ISDN switch to receive and decompress, compress and transmit
ISDN BRI digital voice traffic. In the downstream direction, the module can be connected to a TE
device to forward the voice packets from the TE device to the Internet through a WAN interface on
the router, thus implementing VoIP. The module has the following features.

•

A BSV interface supports two modes: user and network, respectively for connecting an ISDN
network and a TE device.

•

When a BSV interface works in network mode, traffic is processed as follows: The digital voice
traffic received on the BSV interface is compressed and forwarded through the CPU on the
main control board to a WAN interface. The IP voice traffic received on a WAN interface is
forwarded through the CPU on the main control board to SIC-1BSV/SIC-2BSV, where the traffic
is decompressed and sent to the TE device.

«
...
35
36
37
38
39
...
»

Содержание DSIC-9FSW




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSIC-9FSW

Бренд: ABB Страницы: 2

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

Controller CR100

Бренд: Sonos Страницы: 2

Бренд: GEM Страницы: 31

Бренд: Pangolin Страницы: 35

Бренд: Raypak Страницы: 2

Бренд: 4D systems Страницы: 6

Бренд: Phoenic Mecano Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды