H3C DSIC-9FSW Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 219

background image

19

Table 27 LED description

LED Description

LINK

•

Off: The link is idle.

•

On: The connection has been established.

•

Flashing: The connection is being set up.

ACT

•

Off: The link is idle.

•

Flashing: Data is being transmitted or received.

Interface cables and the connection methods

For more information about the Ethernet interface cables and the connection methods, see
"

ADSL/BS/FXS/FXO/AM/FCM interface

."

XDSL interface module

•

SIC-1ADSL

•

SIC-1ADSL-I

SIC-1ADSL

Introduction

The 1-port ADSL over PSTN interface module (SIC-1ADSL) provides an RJ-11 interface that can
work as a WAN interface. It allows a LAN subscriber to connect to the digital subscriber's loop
access multiplexer (DSLAM) at the central office over a regular analog subscriber line or telephone
line. Thus, the subscriber can access the ATM/IP backbone or the Internet to enjoy services such as
high-speed data communication and video on demand (VoD).

ADSL transmits data in the high frequency band above 26 kHz. Therefore, it can provide services
without interfering with the voice service being provided in the low frequency band (0 to 4 kHz) on the
same line. It provides downlink rates in the range 32 kbps to 8 Mbps and uplink rates in the range 32
kbps to 1 Mbps.

The SIC-1ADSL delivers these features:

•

Manual ADSL line activation and deactivation, providing a convenient fault location means.

•

Interface standards of G. DMT, G. Lite, and T1.413, autosensing.

•

Trellis coding (except for G. Lite) on ADSL interfaces, enhancing the stability of ADSL
connection.

«
...
26
27
28
29
30
...
»

Содержание DSIC-9FSW




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSIC-9FSW

FEPL-02 Ethernet POWERLINK

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 2

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: BADODOSECURITY Страницы: 8

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: DayTronic Страницы: 22

Бренд: DayTronic Страницы: 414

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: olympia electronics Страницы: 10

Бренд: Taoglas Страницы: 2

Бренд: Saluki Страницы: 13

Бренд: WAGNER Страницы: 60

Бренд: Balboa Water Group Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды