manualshive.com logo in svg

H3C CR16000-F, Руководство пользователя

Поделиться
Скачать
H3C CR16000-F Скачать руководство пользователя страница 12

 

11 

By default, Ethernet interfaces are in the non-synchronous mode. An interface can participate 
in the clock reference selection only when it is in the synchronous mode. 

4. 

Enable ESMC to transmit QL information. 

esmc enable

   

By default, ESMC is disabled on Ethernet interfaces. 

Display and maintenance commands for SyncE 

Execute 

display

 commands in any view. 

 

Task Command 

Display ESMC information. 

display esmc 

[

 

interface

 

interface-type 

interface-number

 

]

 

 

Synchronous Ethernet configuration examples 

Example: Configuring synchronous Ethernet 

Network configuration 

As shown in 

Figure 2

, configure SyncE between the devices. 

Figure 2 Network diagram 

 

 

Procedure 

# On Device A, enable the synchronous mode and ESMC on Ten-GigabitEthernet 3/1/1. 

<DeviceA> system-view 

[DeviceA] interface ten-gigabitethernet 3/1/1 

[DeviceA-Ten-GigabitEthernet3/1/1] synchronous mode 

[DeviceA-Ten-GigabitEthernet3/1/1] esmc enable 

[DeviceA-Ten-GigabitEthernet3/1/1] quit 

# On Device B, enable the synchronous mode and ESMC on Ten-GigabitEthernet 3/1/1. 

<DeviceB> system-view 

[DeviceB] interface ten-gigabitethernet 3/1/1 

[DeviceB-Ten-GigabitEthernet3/1/1] synchronous mode 

[DeviceB-Ten-GigabitEthernet3/1/1] esmc enable 

[DeviceB-Ten-GigabitEthernet3/1/1] quit 

Verifying the configuration 

# Verify that ESMC is enabled on both Device A and Device B when they are connected to their 
respective clock references. The clock QLs of Device A and Device B are 

QL-PRC

 and 

QL-SEC

, 

respectively. Device A provides more precise timing than Device B.   

[DeviceA] display esmc 

Interface   :  Ten-GigabitEthernet3/1/1 

Содержание CR16000-F















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды