H. Wilson Company
2245 Delany Road
Waukegan, IL 60087
Phone: (800) 245-7224
Fax: (800) 245-8224
Email: [email protected]
Visit: www.hwilson.com
Parts List
(1) Top Shelf (18”W x 16”L)
(1) Adjustable Shelf (18”W x 18”L)
(1) Middle Shelf (15”W x 15”L)
(1) Bottom Shelf (15”W x 30 1/2”L)
(1) Modesty Panel (18"L x 16 1/2"W)
(1) Left Side Frame
(1) Right Side Frame
(4) Plastic Plugs
(4) Stickers
(1) Wrench
(4) Flat Washers
(4) Spring Washers
WPS4E, WPS4BRE, &
WPS4BR5E
A. (2) Locking 3” Casters
B. (2) Non-locking 3” Casters
C. (24) 3/4” Panhead Screws
D. (4) 2" Flathead Screws
E. (4) 2” Panhead Screws
F.
(2) Support Brackets for Second Shelf
G. (4) Small Brackets for Top Shelf
H. (4) Locking Nuts
Allen Wrench Included
Instructions for Open Shelf (No
Cabinet):
1. Take one of the side frames and lay flat. Attach bot-
tom shelf to side frame using (2) 2" flathead screws &
locknuts. Take frame assembly and position it so that
the side panel is resting on the back edge and the shelf
is in a vertical position. Attach the second side frame
panel to the bottom shelf. (Figure 1)
2. To attach the casters, insert first the spring washer,
then the flat washer over the stem in the caster. Screw
in threaded caster. Do the same for all (4) casters,
making sure that the locking casters are on the same
side. Tighten casters with wrench that is provided.
(See
Image #1)
3. Take Modesty Panel (18" x16 1/2") and attach using
(8) 3/4” screws (C).
(See Image #4)
. Attach to side of
panels where the bottom shelf extends further out.
4. Attach middle shelf (15” x 15”) (one flat side/one
rounded side) using (4) 2" screws (E). Put screws
through the guide holes that are on the side panels
making sure that flat side of shelf is flush with the side
where the bottom shelf extends further out.
(See Image
#2)
5. Take top shelf (18” x 16”) and attach the (4) small
“L” shaped brackets (G) to the underside of the shelf.
(See Image #3)
The brackets have two different style
holes on them (perfectly round and oval). Attach the
round side to the bottom of the shelf using (4) 3/4” (C)
screws, making sure that the other side of the bracket
is facing towards the outside of the shelf. When attach-
ing shelf to top of side panels make sure the “L” brack-
ets line up with the pre-drilled holes on the side panels.
Attach using (4) 3/4” screws (C).
If you have purchased a unit with a
cabinet please refer to
WPS4CE, Cabinet
Instructions on Page 2.
2
3
Page 1 of 3
REVISED 12/09
1
Important Assembly Tip:
When assembling
a WPS4E OR a
WPS4CE, do not
tighten the screws all
the way down. Leave
them approximately 1/2
turn out. When unit is
fully assembled, tighten
screws all the way. This
will allow the unit to line
up correctly.
NOTE: The 'BR' and 5 in the model number is a color designation.
WPS4E Is the same unit as WPS4BRE and WPS4BR5E. WPS4CE is the
same as WPS4BRCE.
