manualshive.com logo in svg

GUITAR KIT WORLD EXP-style Guitar Kit, Инструкция по сборке

Поделиться
Скачать
GUITAR KIT WORLD EXP-style Guitar Kit Скачать руководство пользователя страница 3

Parts List

Below are the parts you will find included in your packaging to complete an EXP guitar kit.

● EXP body and neck
● Neck plate, neck plate cushion and screws (if bolt-on neck)
● 2 x Strap buttons
● 6 x in-line tuners
● Stud mounted Tune-O-matic style bridge with tailpiece
● Neck and bridge humbuckers
● 2 x volume, 1 x tone controls, 1 x capacitor, 1 x 3 way pickup selector, and input jack
● Truss rod cover, pick guard and electronics cavity cover
● Cable and hex wrench (for adjusting truss rod)
● Tone and volume knobs
● Assorted screws and washers

Safety Precautions

To complete your guitar kit safely, also ensure you have the following on hand, and a well
ventilated work space to work in.

Protective eyewear

Use protective safety glasses or a genuine face shield, not regular prescription, reading, or
sunglasses.

Disposable gloves

Use disposable gloves if applying stains or oil finishes directly to the guitar.

Masks

Use an N95 rated dust mask for sanding and an R95 rated particle mask for finishing. If
using water based finishing products an N95 dust mask may suffice for both sanding and
finishing, but be sure to check the finishing suppliers recommendations first. Paint fumes
are dangerous.

3

Содержание EXP-style Guitar Kit
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды