background image

 

11

OPERATING THE CHARGER – 20 amp output 

 

The LED Function Chart describes the charging process for any individual 20 Amp output.

 

Display 

Operating condition 

When the red LED is on, it indicates that your batteries are discharged and is 

recharging  them  at  the  "Charging"  rate  (stage  1).  This  charging  rate  is  20 

Amps. 

While the red LED is on, the voltage measured (with the charger on) will be 

approximately 11.5 to 13 Volts. 
If  the  red  LED  stays  on  for  more  than  24  hours,  refer  to  Problem  1  in  the 

troubleshooting section in this manual.

 

When  both  the  green  and  the  red  LED’s  are  on,  it  is  charging  at  the 

"Finishing"  rate.  (stage  2).    During  this  second  charging  stage,  the  charger 

holds  the  battery  voltage  at  approximately  14.3  VDC,  and  then  gradually 

reduces the amount of current (Amps) it delivers to the battery.  By doing this, 

the battery is able to “absorb” the last 10% of charge as quickly as possible 

without becoming overheated.   
If  both  lights  stay  on  longer  than  24  hours,  refer  to  Problem  2  in  the 

troubleshooting section in this manual. 

 

When the battery approaches full charge, the charger switches into its third 

charging stage, gradually reducing the current fed to the batteries to as low as 

0.1  Amps.    At  the  same  time,  it  reduces  its  output  voltage  to  a  “Float”  or 

“Ready” charging rate of approximately 13.3 VDC, indicated by the green LED 

light.    This  low  “

Float”

  or 

“Maintenance”

  voltage  gently  “tops  off”  your 

batteries, keeping them fully charged and ready until needed.  The green LED 

indicates that your batteries are now fully charged and ready for use. 

If  the  green  LED  stays  on  when  your  battery  is  known  to  be  low,  refer  to 

Problem 3 in the troubleshooting section in this manual. 

 

 

 

 

 

 

 

 

 

 

Содержание Cruising Charger 2632A















Отзывы: