Gude Expert Net Control 2304 страница 33 Скачать руководство пользователя

Страница: 33 / 87

Expert Net Control 2304

Configuration

Telnet TCP port: Telnet sessions are accepted on this port.

Raw mode: The VT100 editing and the IAC protocol are disabled.

Activate echo: The echo setting if not changed by IAC.

Active negotiation: The IAC negotiation is initiated by the server.

Require user login: Username and password are required.

Delay after 3 failed logins: After 3 wrong entries of username or password, the next lo-
gin attempt is delayed.

Use radius server passwords: Username and password are validated by a Radius
Sever.

Use locally stored passwords: Username and password are stored locally

3.4.2

Syslog

Enable Syslog: Enables the usage of Syslog Messages.

Syslog Server: If you have enabled Syslog Messages, enter the IP address of the
server to which the syslog information should be transmitted.

3.4.3

SNMP

Содержание Expert Net Control 2304
























































































Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Похожие инструкции для Expert Net Control 2304

Бренды по названию

Популярные бренды

Gude Expert Net Control 2304, Руководство пользователя

Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Похожие инструкции для Expert Net Control 2304

Бренды по названию

Популярные бренды