GÜDE 40631, Оригинальная инструкция по эксплуатации, Страница: 16 / 52

Observe strictly the rules for disposal of w aste
oil and dispose of it properly in a w aste oil collection
center.
Unscrew the drain screw is now firmly back on and fill
oil up to the m ark on the dipstick
In w inter we recommend a lubricity oils to start
during the cold season to help!
Handling (pic. 1,2)
Turn the com pressor never about the power,
otherwise no discharge of the unit is done. Without
discharge, the electric m otor through the back pressure
dam age!
The plug needs to be pulled out of socket before
each adjusting or m aintenance of the com pressor.
Sw itching on or off
•
The compressor can be sw itched on by pulling the
sw itching button and sw itched off by pushing the
button.
Working pressure control
•
The w orking pressure can easily be adjusted, turn the
rotary knob
in the + direction , by this the w orking
pressure is increased . Turn the rotary knob in the –
direction , by this the w orking pressure is
decreased. There is an autom atic safety valve
releasing pressure at overpressure. The pressure
can be released by hand by pulling the valve ring.
ATTENTION:
Ensure necessary volume delivered of your pneumatic
appliance! The pressure itself IS NOT decisive for a
faultless or sufficient operation. Sw itching the compressor
on for a short time follow ing a long shut-dow n w ithout using
it is normal!
Have any scheduled repairs explicitly executed by a trained
professional staff.
Inspections and m aintenance (pic. 9)
Alw ays pull the plug out of socket before each w ork on the
appliance. Before any long period of not using of the
compressor it is necessary to give a few oil drops on the air
filter w asher – compressor cylinder w alls w ill prematurely be
lubricated at the next start.
•
To clean the plastic parts, use a damp cloth. Do not use any
cleaners, solvents or sharp objects.
•
After each use, remove any settled dust from air holes and
mobile parts w ith a soft brush.
Regularly lubricate all mobile metal parts w ith oil.
After each use
Remove dust from air holes and mobile parts.
Regularly
Lubricate mobile metal parts w ith oil (multipurpose oil)
Check w hether all screw s are firmly tightened.
Regularly (at least once a month) remove condensation from the air
jet otherw ise your rust guarantee w ill expire – apart from this
activity, the compressor is maintenance-free
(due to the air jet surface, the condensation can get brow n).
1.
Pull the plug out of socket!
2. Open the sludge valve (pic. 9/a) at low voltage in the air jet
(max. 1 bar) and completely empty the condensation (use a
suitable container)
3. Close the valve.
Overheating fuse:
If the compressor has any technical defect or is burdened w ith a
continuous run the current supply is automatically interrupted by a
thermal sw itch. Should this situation occur, it is suitable to
disconnect the compressor from netw ork and leave it cool dow n for
app. 5 minutes. If the compressor fails to start after some time of
w orking leave it cool dow n for other 3 minutes.
Air-pressure switch:
The compressor is fitted w ith an automatic air-pressure sw itch that
is sw itched off by the compressor after reaching a maximum service
pressure and sw itched on at repeated need of air. Sw itching
pressure of 6 bar, max. pressure of 8 bar.
V-belt
Check the tension of the regular V-belt.
Should it be necessary to tighten the fan belt, proceed as follow s:
•
Remove the 4 screw s of the motor.
• Tighten the fan belt by pressing aw ay from the motor unit.
• Is the fan belt eager to have the screw s of the motor re-
attached.
• Be sure the tw o pulleys to escape each other.
Air filter
Sometimes it is necessary to clean the air filter insertion. To do that,
take the w ing-nut out of the air filter cover and remove the foam
filter. The filter can be cleaned w ith w arm soap suds. Dry and
reinsert the foam filter. Fix the air filter cover again.
16