DRILLING & INSTALLATION INSTRUCTIONS:
1.
Drill a 3/4” (19mm) diameter hole at least 3.5” (89mm) deep. The drilled hole must be straight and perpendicular
to the surface. Make sure the hole is of uniform diameter and free of peaks and valleys on the inner wall.
2.
Blow hole clean with compressed air.
3.
Always inspect the hole carefully when reusing a previously drilled hole.
4.
When placing anchor, place your thumb inside the anchor loop and your first two fingers around the trigger.
Squeeze fingers and thumb together till the trigger and spring fully compress.
5.
Insert unit at least 3” (76mm) deep into hole and release the trigger. (Do not force.)
6.
Set the unit with a slight tug on the anchor loop.
7.
The stop sleeve must always be partially inserted into the hole.
All products subjected to fall arresting forces should be removed
from service immediately!
DECK/FLOOR/GROUND LEVEL
WORK SURFACE
(ANCHOR POINT)
MINIMUM CLEARANCE 3ft (1m)
W
ARNING!!! SWING F
ALLS C
AN OC
CUR
WHEN
THE
W
ORKER IS NO
T DIREC
TL
Y UNDER ANCHOR POINT
.
Free fall distance (limit) must
not exceed 6’ (1.8 m).
The concrete must be
3000-psi or higher and
fully cured. Installation
location to be approved
by a qualified person.
Spoon
Cleaning Bushing
Spring
Swage
Anchor Loop
Heavy Duty Return Wire
Stop Sleeve
End Termination
Trigger
1.25” (31mm)
3.0” (76mm)
7.0” (178mm)
11.5” (293mm)
Main Cable
2” (50.8mm)
REMOVAL INSTRUCTIONS:
1.
When removing anchor, place your thumb inside the anchor loop
and your first two fingers around the trigger. Squeeze fingers and
thumb together till the trigger and spring fully compress.
2.
While squeezing the trigger pull the anchor out of the hole.
3.
If the anchor becomes stuck, insert a punch, screwdriver or other
object into the hole until it touches the top of the cleaning bushing.
4.
Lightly tap with a hammer making sure the tool is touching the top
of the cleaning bushing while squeezing the trigger. (The cleaning
bushing should be easily visible at the edge of the hole).
5.
If tool was required to remove the anchorage inspect thoroughly for
damage after removal. If damage is found remove from service and
destroy immediately.
WORK SURFACE
May be used as a anchoring point for a leading
edge restraint system. Examples are of optional
anchoring point locations. The use of two anchors
is not required for leading edge restraint systems
unless otherwise specified by the manufacturer.
OPTIONAL
(ANCHOR POINTS)
(A)”
drill
3/4”
Ø
min from
any edge
(B)”
HOLE DRILLING REQUIREMENT CHART
(A)” Minimum distance from edge/corner
(B)” Concrete thickness
6” in. (15.3 cm)
12” in. (30.5 cm)
12” in. (30.5 cm)
5” in. (12.7 cm)
V1.4
PERFORMANCE:
Static Tensile Strength:
5000-lbf (22kN)
Maximum Capacity:
one worker with
max weight of 310-lbs when used as a
single point anchorage connector for
personal fall arrest or restraint system.
DIMENSIONS:
Weight:
.44-lbs (200g)
Length:
11.5” (349mm)
Diameter
.75 (19mm)
REGULATORY COMPLIANCE:
ANSI Z359.1-2007, ANSI Z359.7-2011
OSHA 1926.502, OSHA 1910.66,
CE 0321 / EN
795:1996 (+A1:2000) Class B
COMPONENT MATERIALS:
Aluminum:
Trigger
Aircraft Cable:
Main Cable, Activator Wire
Polyurethane:
Loop Cover
Stainless Steel:
Cone, Spoons, Stop Sleeve
Zinc Plated Steel:
Spring
Zinc Plated Copper:
Swage
TAP!!!
DO NOT REMOVE
WARNING LABEL!
Inspect before each use. In addition , a competent person must inspect at least annually
INSPECTION LOG
Date
Initial
Compliance:
OSHA 1926,502 & 1910.66
ANSI Z359.1
Max capacity 400 lbs.
(ANSI Z359.1- 310 lbs)
G-Bolt
TM
1-800-466-6385
Model #
( ) -00235 (3/4” 5,000 lbs.)
( )- 00365 (3/4” 5,000 lbs.)
( )- 00236 (1” 10,000 lbs.)
(Breaking strength rating)
Do Not Remove Label
US Patent 6,729,821
US Patent 7,011,281
US Patent 7,357,363
Lot #
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
MFG. Date
M
Y
1 2 3 4 5 6
7 8 9 10 11 12
11 12 13 14 15
Made in the USA
WARNING DO NOT use in wet or uncured concrete.
Use in normal weight concrete with a compression
Strength at least 3,000 PSI (20.7 MPa) Use for Fall
Protection Only.
* Do not use with incompatible connectors.
* Avoid physical hazards suck as thermal, electrical
and chemical sources.
* Avoid contact with sharp edges and
Abrasive surfaces.
Warning:
All persons using this equipment must
read, understand and follow all
Instructions. Failure to do so may result in
serious injury or death.
Reference instruction manual supplied
with the product for proper installation
procedures.
Materials:
* Stainless steel
* Aluminum alloy
* Zinc plated copper
*7x19 aircraft cable
Inspe
ct b
efo
re each us
e.
In
addi
tion
,
a
compe
tent pe
rson
must
inspect
at
le
as
t a
nnua
lly
IN
SPECT
IO
N
LO
G
Date
Initial
