background image

 

19 

 
 
 

 

      

WARNING:

 

When servicing, use only original equipment replacement parts. The use of any 

other parts may create a safety hazard or cause damage to the oscillating tool. 
 
Any attempt to repair or replace electrical parts on this oscillating tool may create a safety hazard 
unless repairs are performed by a qualified technician. For more information, call the Toll-free 
Helpline, at 1-866-349-8665 Monday 

– Friday from 9am to 5pm Eastern Standard Time.

 

 
Always order by PART NUMBER, not by key number. 

 
 

Key # 

Part # 

Part Name 

Quantity 

4030010114 

Screw ST3.9X25 

3110010140 

Gear housing  

2020050031 

E-ring 

4020080032 

Bearing 

2030020177 

O-ring 

4100010003 

Bearing support 

3140130003 

Ball bearing 608-2Z 

4010020005 

Baffle 

2030200004 

Needle bearing 

10 

4010010055 

Fork 

11 

2040290048 

Ball bearing 6001-2RS 

12 

4100050001 

Inner ring 

13 

4010050002 

Rubber washer 

14 

3140020049 

Output shaft 

15 

2020130027 

Washer 

16 

4010010036 

Bolt 

17 

3120010050 

Level knob 

18 

3150050047 

Switch level 

19 

1020210004 

Rotor 

20 

3120110040 

Stator 

21 

1010210004 

Carbon brush assembly 

22 

1230010059 

Brush holder 

23 

2030070001 

Brush holder support 

24 

3150060005 

Ball bearing 607-2Z 

25 

4010010035 

Motor housing 

26 

1061150016 

Cord guard 

27 

3150160117 

Hex key 

28 

1130080009 

Power cord 

29 

4030010026 

Switch 

30 

3011210004 

Switch support 

31 

3140060014 

PCB 

32 

4060090009 

Rubber cap 

33 

3140010032 

Handle cover 

34 

1190030008 

Screw ST3.9X19 

PARTS LIST 

Содержание 172485





















Отзывы: