background image

2

3

ABC 

DEF 

GHI 

JKL 

MNO 

PRS 

TUV 

WXY 

Keypad Description

Installing Batteries

Step 1: Remove the two screws from the bottom of the keypad (FIG. 3) and separate the keypad from its housing.
Step 2: Install 3 AA batteries (not included). (FIG. 2NOTE: Choose wireless or wired  
installation (not both) and proceed to appropriate section.

1

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PRS

8

TUV

9

WXY

0

STATUS Light:

The LED will blink once when 

any key is pressed and provides 

visual feedback during access 

code programming.

PROGRAM Button:

Use for / during program process.

Keypad - Front

Battery Holder:

Use 3 AA batteries.

OUT  COM.

RESET

+

– +

+

RESET Button:

Pressing this button for 2 seconds will 

reprogram keypad to factory settings. All 

codes are deleted. Default master code is 1234.

Open Collector Output:

Used to connect Keypad to gate opener that 

accepts logic inputs (All GTO gate openers) 

in hard-wired applications.

Keypad - Inside

Wireless Installation of the Keypad

NOTE: For wireless applications, the distance from the keypad to the opener’s receiver 

should not exceed 50 ft. Always test the keypad range before permanently mounting it.
Step 1: Mount the keypad cover using the screws provided.

Step 2: Slide the keypad into the cover and secure with the small screws provided.

NOTE: If you have not changed your opener’s transmitter code from the factory setting, 

see the “Setting Your Personal Transmitter Code” section in the gate opener’s manual then 

“Learn” the transmitter code into the keypad. See “Learn Transmitter Code” section below.

 

1

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PRS

8

TUV

9

WXY

0

 

 Press and release the PROGRAM button.

 

 Enter the Master Code then press and release the 

PROGRAM button.

 

 Enter 0,5 then press and release the PROGRAM button.

 

 Press and hold the transmitter button while holding the 

transmitter to the bottom of the keypad as shown.

 

 The keypad will beep 3 times to confirm that the 

transmitter is successfully “Learned.” Release the

 

transmitter button at this time.

Example: Learn transmitter code with Master Code of 

“1234”. Then press and hold transmitter button until you hear 

3 beeps. The round black dot is the “PROGRAM” button.  

Go to “Programming the keypad” to change the master code 

(if desired)

Turn the gate opener back on and confirm that the keypad 

operates the gate using the master code.

1  2  3  4     0  5     

NOTE: 3 AA batteries are required to power the keypad.

FIG. 1

FIG. 2

FIG. 3

FIG. 4

ABC 

DEF 

GHI 

JKL 

MNO 

PRS 

TUV 

WXY 

ABC 

DEF 

GHI 

JKL 

MNO 

PRS 

TUV 

WXY 

IMPORTANT: Make sure the transmitter operates 
the gate opener.
Turn off the gate opener
 so that there is no unintended 

operation of the gate during the learning process.

“Learn” Transmitter Code

 

(for wireless installation)

IMPORTANT: Transmitter must be placed exactly as shown, and against the bottom of 
the keypad in order for the “learning” process to work correctly.

Press & 
Release 
Program
Button.

Enter Master
Code, Press 
& Release 
Program
Button again.

Enter 

0    5     

Press &  
Release 
Program
Button again.

Press and hold 
the transmitter 
button holding 
it to bottom of 
keypad.

Keypad will 
beep 3 times. 
Release the 
transmitter 
button.

Содержание FM137-G3









Отзывы: