manualshive.com logo in svg

GSL electronics BMPPT250, Руководство по эксплуатации

Поделиться
Скачать
GSL electronics BMPPT250 Скачать руководство пользователя страница 7

Page 7 of 8

Model:

BMPPT250

Unit 2, 110 Station Road, Seven Hills ,NSW,  2147, Australia

250W Solar Charger

Booster Maximum Power Point Tracker

Operating Instructions

Please read these instructions before use

Wiring The Remote Alarm:

The remote alarm is a normally low, 5V digital signal that goes high when the battery voltage drops below 
0.9 of nominal voltage, the LVD disconnects or over temperature trips. It has a 5mA source capability and 
can be used to remotely monitor system status.

Wiring With Load Remote Control:

This option enables the remote load connection and disconnection via the load remote control, 

yellow wire. When the yellow wire is grounded the load is disconnected otherwise the load is 
connected. To configure this mode the green wire must be grounded. This option overrides the LVD 

or DDS function but has the same load limitations of 10A continuous or 20A transient.

Grey

LOAD

Green

Yellow

BMPPT250-R4

Buzzer, LED

PC I/O 5V 5mA

+

-

Blue

Black

Please ensure that your BMPPT has been correctly configured (REN & CHE settings) for 

your application. Refer to the Settings and Configurations section for more information. 

Содержание BMPPT250









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды