manualshive.com logo in svg

GSI Group PNEG-1049, Руководство по сборке и эксплуатации

Поделиться
Скачать
GSI Group PNEG-1049 Скачать руководство пользователя страница 24

4. Assembly

24

PNEG-1049

 10"-12" Commercial Bin Sweep Augers

23. Make final adjustments to the back shields and mounting brackets and tighten all hardware. Adjust 

the carrier wheel assemblies if provided. The carrier wheel assembly should NOT be adjusted to 
support the full weight of the flight and shield sections. The carrier wheel assembly should be 
adjusted so that it ONLY keeps the flight and back shield from contacting the floor.

NOTE:

 

Failure to properly adjust the carrier wheel assembly as described above can result in 
damage to the bin floor and the bin sweep.

24. Inspect the “DANGER” decals on the back shields to ensure legibility. If the decal cannot easily be 

read or is missing, order a new decal immediately from the dealer.

25. Fill the 3:1 aluminum enclosed drive with oil. This is accomplished by removing the vented fill plug 

and pouring 48 ounces of oil into the drive. The oil level can be checked by removing the check plug 
on the opposite side of the drive. The oil level should not be over the check plug.

26. Sandwich the front top and bottom motor clip onto the motor rods using two (2) 3/8" x 3" carriage 

bolts and nylock nuts. Sandwich the back top and bottom motor clip onto the motor rods using 
two (2) 3/8" x 3" carriage bolts and nylock nuts. DO NOT TIGHTEN the nuts at this time. They will 
need adjustment when the motor is installed. 

(See Figure 4T.)

 

Figure 4T Motor Clips to Motor Rod

Oil must be added prior to running the bin sweep. The 3:1 aluminum enclosed 
drive is shipped WITHOUT oil.

Do NOT add more oil than is recommended. Additional oil may damage the seals 
or be forced out through the vented fill plug.

For lubrication in normal operating temperature between 40°F and 120°F, we 
recommend the use of non-foaming, multi-purpose gear oil, SAE 90 weight. For 
temperatures below 40°F, use SAE 80 weight oil. Use grade commercially 
available for automotive differentials. Extra pressure additives may be of value in 
severe applications.

Содержание PNEG-1049

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды