GRUNDIG Service
THARUS 51 LCD 51-9410 DOLBY
1 - 11
Service and Special Functions
Call up the Service Menu:
Button "
i
" (EASY DIALOG)
Call up the dialogue line:
Buttons "
P+
" / "
P-
" –> "
OK
"
Changing the setting in the dialogue line: Buttons
"
Ǹ
" / "
Ƿ
"
–> "
OK
"
Back to previous menu:
"Blue" button
Exit menu:
Button "
i
"
Service menu for retailer (code number): "8500"
1. Switching-on Options
1.1 ATS Reset
Press mains button "ON" while holding down the "
Ƿ
" button on the
remote control.
– The basic analogue values are loaded.
– The ATS bit is set. When switching on the next time, this option
releases the ATS euro plus function. The current programme
allocation (channels) is cleared.
1.2 Electronic Programme Lock (parental lock)
Enter the key sequence "7 0 3 8 5 8 0" to cancel your personal code
number.
1.3 Software Version Number
Call up the "EASY DIALOG" menu. Pressing the green button indi-
cates the software version number.
1.4 Flash Programming
Required equipment
Flash programmer F-Prog 1 / from version 2.0 on or
Service Toolbox part number 772004001200.
Required hardware
Pentium-PC, Microsoft Windows 95
– Free memory of 32MB
– CD-ROM drive
– COM port
– Internet access
Calling up the current TV software
The software can be called up from an area of the Grundig partnerweb
(B2B), protected via a Grundig customer number and a password.
Note to downloading the software:
– Start the Internet Browser.
– Input the address http://partnerweb.grundig.com and start.
– Follow the menu guide in "Service –> Software Download".
1.5 Direct Display Type Adjustment
If the menus can not be displayed any longer due to an incorrect display
type adjustment, you can carry out the correct adjustment with the help
of key short cuts.
Before and after the direct entry, the unit must be switched off and on
again!
The "
i
", "red" and numeric keys select the desired display type in the
service mode. The following digits indicate the display types:
1
LPL LC201V1
2
LPL LC201V02
3
LPL LC230W01
4
LPL LC300W01
5
LPL LC420W01
2. Special Functions in the "Installation" Menu
2.1 Entry of Letters
Call up the "Letter entry" menu via "EASY DIALOG" –> "Installation"
–> "Special functions".
You may select between "off", "on" and "mix" for the programme
selection letter entry.
2.2 Visible or Unvisible "Sound scale" for all Programmes
Call up the "Sound scale" menu via "EASY DIALOG" –> "Installation"
–> "Special functions".
With "off" selected, no volume bar is displayed.
2.3 Switching on with Programme "1" or automatically
Call up the "Switch on" menu via "EASY DIALOG" –> "Installation" –>
"Special functions" .
Set the option "Preset 1" or "Automatic".
With the "automatc" setting, the programme position selected when
switching off is selected again when switching the set on again (Last
station memory).
2.4 "Megalogic Info" (only if a connected Megalogic set is identified)
Call up the "Megalogic info" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
The Megalogic control can be switched to "on" or "off".
2.5 Status Display
Call up the "Status Display" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
You may select the position (top or bottom) where the information
about the sound mode and the picture format is displayed.
With the "off" option, no information is displayed when changing the
programme.
2.6 Automatic Volume
Call up the "Automatic volume" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
In the "ON" position, the sound IC regulates the volume internally to
the normal value (e.g. increased deviation in the case of advertising).
2.7 Noise Reduction P1-P…
Call up the "Noise reduction P1-P…" menu via "EASY DIALOG" –>
"Installation" –> "Special functions. For the programmes 1-P… you
may set the noise reduction to "off", "low" or "automatic".
"Manual" indicates that one or several programmes have different
settings.
2.8 Picture Sharpness P1-P…
Call up the "Sharpness P1-P…" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
The picture sharpness is set for all programmes.
2.9 Colour Match
Call up the "Colour match" menu via "EASY DIALOG" –> "Installation"
–> "Special functions".
The colour match (luma delay) is set for every programme.
3. Service Settings for the Retailer
3.1 Picture Settings
3.1.1 White Balance
Call up the "White balance" menu via "EASY DIALOG" –> "Installation"
–> "Dealer service menu" –> Code number "8500" –> "Picture settings".
Adjust the values for "red", "green" and "blue" so that a white picture
is obtained (see Alignment, Point 5).
Note:
When calling up the menus again, the value of the largest component
is always 511, the other values are converted.
3.1.2 AD Converter
Call up the "Automatic – Yes" menu via "EASY DIALOG" –> "Installa-
tion" –> "Dealer service menu" –> Code number "8500" –> "Picture
settings" –> "@AD-Wandlerabgleich".
Call up the "@Automatischer Abgleich starten" menu and wait up to the
menu that is shown on the display.
If it necessary the AD Converter can be adjusted manually.
– Call up the "Automatic – No" menu via "EASY DIALOG" –> "Instal-
lation" –> "Dealer service menu" –> Code number "8500" –>
"Picture settings" –> "@AD-Wandlerabgleich".
– Black Level Balance
– Select the AV position (black picture) on the TV set.
– Call up the "Black level balance" menu.
– Adjust the "red", "green" and "blue" values in such a way that the
transition of the colour scale (test pattern) is at the same place for
all 3 colours (R,G,B just visible). The control values for the
components should remain as close as possible to the given value
248.
– Adjust the offset in such a way that the colour window is located
inside the centre frame.
