manualshive.com logo in svg

Grundig GSS SID 162 A, Инструкция по сборке

Поделиться
Скачать
Grundig GSS SID 162 A Скачать руководство пользователя страница 7

 

 

- 7 - 

SID 162 A

4 

i

nstalling

 

the

 sat if 

input

 

distributor

  Before installing or changing a module or accessory, switch off the head-end 

station or unplug the power cable from the mains power socket.

 

Installing the SAT IF input distributor take care that no cables are squeezed off 
or injured. 

 

•  Remove the front cover – and if present – the bottom plate of the head-end 

station.

 

•  Mount the SAT IF input distributor in the respective bushings. Therefore ob-

serve the assembly instructions of the corresponding head-end station. 

 

•  Insert  the  SAT  IF  input  distributor  so  into  the  head-end  station  that  the 

LNB power connection 

A

 is facing the control panel and no cables are 

squeezed off or injured.

 

•  Fasten the outer sockets of the SAT IF input distributor 

G

 with nuts and lock 

washers put under each.

 

 

G

G

A

  Tighten the nuts until the teeth on the lock washers have penetrated the exte-

rior coating and a good connection is made between the housing and the SAT 
IF input distributor.

Содержание GSS SID 162 A












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды