background image

English (GB)

7

7. Storing and handling the product

The pump can be transported in a vertical or horizontal position. 
Make sure that it cannot roll or fall over.

7.1 Storing the product 

During long periods of storage, protect the pump against moisture 
and heat.
If the pump has been in use, change the motor liquid before 
storage. See section 

10.3 Checking and changing the motor oil

.

After a long period of storage, inspect the pump before putting it 
into operation. Make sure that the impeller can rotate freely. Pay 
special attention to the shaft seals, O-rings, motor oil and cable 
entry.

7.2 Transporting the product

Make sure that all lifting equipment is rated for the purpose. 
Check the lifting equipment for damage before making any 
attempts to lift the pump. Do not exceed the rating data under any 
circumstances. For pump weights, see the pump nameplate, 
section 

4.1 Nameplate

.

The polyurethane-embedded plug prevents water from entering 
the motor via the motor cable.

7.3 Lifting the product

The SEG AUTO

ADAPT

 pumps weigh between 38 kg and 65 kg 

without accessories. It is therefore essential to use the correct 
lifting equipment.

When lifting the pump, use the correct lifting point to keep the 
pump balanced. Place the lifting chain hook in point A for auto-
coupling installations and in point B for other installations. See 
fig. 

5

.

Fig. 5

Lifting points

7.4 Contaminated products

See section 

2. Returning the product for service

.

WARNING

Instable pump

Death or serious personal injury
- Always lift the pump by its lifting bracket or by 

means of a forklift if the pump is fixed on a pallet. 
Never lift the pump by means of the motor cable or 
the hose/pipe.

Rate all lifting equipment for the purpose and check it 
for damage before making any attempts to lift the 
pump. Do not exceed the lifting equipment rating 
under any circumstances.

TM

06 006

6 481

3

CAUTION

Biological hazard

Minor or moderate personal injury
- If a pump has been used for a liquid which is 

injurious to health or toxic, the pump will be 
classified as contaminated.

Содержание seg autoadapt



























Отзывы: