background image

Limited Warranty

Products  manufactured  by  GRUNDFOS  PUMPS  CORPORATION 
(GRUNDFOS)  are  warranted  to  the  original  user  only  to  be  free 
of  defects  in  material  and  workmanship  for  a  period  of  24  months 
from date of installation, but not more than 30 months from date of 
manufacture. GRUNDFOS' liability under this warranty shall be limited 
to repairing or replacing at GRUNDFOS' option, without charge, F.O.B. 
GRUNDFOS'  factory  or  authorized  service  station,  any  product  of 
GRUNDFOS  manufacture.  GRUNDFOS  will  not  be  liable  for  any 
costs  of  removal,  installation,  transpor-tation,  or  any  other  charges 
which may arise in connection with a warranty claim. Products which 
are  sold  but  not  manufactured  by  GRUNDFOS  are  subject  to  the 
warranty provided by the manufacturer of said products and not by 
GRUNDFOS' warranty. GRUNDFOS will not be liable for damage or 
wear to products caused by abnormal operating conditions, accident, 
abuse, misuse, unauthorized altera-tion or repair, or if the product was 
not installed in accordance with GRUNDFOS' printed installation and 
operation instructions.

To obtain service under this warranty, the defective product must be 
returned  to  the  distributor  or  dealer  of  GRUNDFOS  products  from 
which it was purchased together with proof of purchase and installation 
date, failure date, and sup-porting installation data. Unless otherwise 
provided, the distributor or dealer will contact the GRUNDFOS factory 
or  authorized  service  station  for  instructions.  Any  defective  product 
to be returned to the factory or service station must be sent freight 
prepaid; documentation supporting the warranty claim and/or a Return 
Authorization must be included if so instructed.

GRUNDFOS WILL  NOT  BE  LIABLE  FOR  ANY  INCIDENTAL  OR 
CONSEQUENTIAL DAMAGES, LOSSES, OR EXPENS-ES ARISING 
FROM  INSTALLATION,  USE,  OR  ANY  OTHER  CAUSES. THERE 
ARE  NO  EXPRESS  OR  IMPLIED  WAR-RANTIES,  INCLUDING 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, 
WHICH EXTEND BEYOND THOSE WARRANTIES DESCRIBED OR 
REFERRED TO ABOVE.

Some jurisdictions do not allow the exclusion or limitation of incidental 
or  consequential  damages  and  some  jurisdic-tions  do  not  allow 
limitations  on  how  long  implied  warranties  may  last. Therefore,  the 
above limitations or exclusions may not apply to you. This warranty 
gives you specific legal rights and you may also have other rights which 
vary from jurisdiction to jurisdiction.  

Grundfos Pumps Corporation
17100 W. 118th Terrace
Olathe, Kansas 66061
Telephone: (913) 227-3400
Fax: (913) 227-3500

Grundfos Canada, Inc.
2941 Brighton Rd.
Oakville, Ontario L6H 6C9
Telephone: (905) 829-9533
Fax: (905) 829-9512

Bombas Grundfos de Mexico, S.A. de C.V.
Boulevard TLC #15, 
Parque Industrial Stiva Aeropuerto
C.P. 66600 Apodaca, N.L. Mexico
Telephone: 52-81-8144-4000
Fax: 52-81-8144-4010

 L-UP-TL-035 

3/07

PRINTED IN USA

Содержание MixiMizer






















Отзывы: