manualshive.com logo in svg

Grundfos LC 108, Инструкция по установке и эксплуатации

Поделиться
Скачать
Grundfos LC 108 Скачать руководство пользователя страница 18

English (GB)

18

7. Systems with 2 electrodes

Description (see also page 

43

 or 

44

):

The pump is controlled by the liquid level in the borehole. 
• The electrode, pos. 1, is the reference electrode.
• When the electrode, pos. 2, registers liquid, the "waiting time" 

is initiated (can be set). After expiration of the waiting time, the 
pump is started.

• The pump is stopped when the electrode, pos. 2, does

 not 

register any liquid. 

• The pressure switch, pos. 3, stops the pump if the discharge 

pressure exceeds the stop pressure of the pressure switch. 
Restarting at the starting pressure of the pressure switch is 
only effected if the electrode, pos. 2, registers liquid.

7.1 Electrical connection

2 electrodes, pages 

43

 and 

44

.

Fig. 

7

 on page 

43

.

The figures show all electrical connections required to connect 
the LC 108 for 

direct-on-line starting, 2 electrodes

.

Fig. 

8

 on page 

44

.

The figure shows all electrical connections required to connect 
the LC 108 for 

star-delta starting, 2 electrodes

. 

The operating voltage and frequency are marked on the controller 
nameplate. Make sure that the controller is suitable for the 
electricity supply on which it will be used. 
All cables/wires must be fitted through the Pg cable entries and 
gaskets (IP65).
Maximum back-up fuse is stated on the controller nameplate.
If required according to local regulations, an external mains 
switch must be installed.

Single-phase motors must be connected to an external operating 
capacitor and in certain cases also to a starting capacitor. 
Further details can be found in the installation and operating 
instructions for the pump in question.

The pressure switch, pos. 3, must be connected as an NC 
contact.

Key to the symbols in fig.  

7

 on page 

43

 and fig. 

8

 on page

44

:

7.2 Setting

2 electrodes, pages 

43

 and 

44

.

The CU 211 module has a 10-pole DIP switch in the bottom right 
corner, see fig. 

14

.

The DIP switch setting offers the following possibilities:
• selection of starting delay and automatic test run (switch 4),
• setting of waiting time (switches 5, 6, 7 and 8),
• selection of automatic alarm resetting (switch 9),
• selection of automatic restarting (switch 10).

Fig. 14

Set the DIP switch as shown in fig. 

14

.

Each individual switch (1 to 10) of the DIP switch can be set to 
position OFF or ON.

Warning
Before starting any work on pumps used to pump 
liquids which could be constituted as being 
hazardous to health, thorough cleaning/venting of 
pumps, pits, etc. must be carried out according to 
local regulations.
Before making any connections in the LC 108 or 
work on pumps, pits, etc., it must be ensured that the 
electricity supply has been switched off and that it 
cannot be accidentally switched on. 

Warning
Before starting work on the system, switch off the 
supply voltage and lock the mains switch in position 
0.
Any external voltage connected to the system must 
be switched off before work is started.

Warning
The LC 108 must be connected in accordance with 
the rules and standards in force for the application in 
question.

Caution

If the PTC resistance/thermal switch of the motor is 
connected, the factory-fitted short-circuit jumper 
must be removed (terminals T11-T21). 

Warning
Float switches or electrodes placed in an explosion 
hazard area must be connected via an EEx barrier, 
e.g. Grundfos number 96440300. The EEx barrier 
must not be installed in the explosion hazard area.
Equipment used in explosion hazard areas must in 
each individual case have been approved for this 
particular application. Furthermore, the cables into 
the explosion hazard area must be laid in 
accordance with local regulations.

Note

The motor/pump housing must not be used as 
reference electrode.

Pos. Description

Terminal 

number

1

Reference electrode.

11

2

Electrode for start/stop of pump.

12

3

Pressure switch.

41-42

Caution

The controller must be off circuit to ensure the 
correct configuration during start-up after change of 
the DIP switch setting.

TM

04 234

2 230

8

Note

The DIP switch must not be set to other switch 
combinations than those described in this section.

Содержание LC 108























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды