background image

2.3 Identification

2.3.1 Nameplate, ALPHA SOLAR

l

1

/

1

(A)

Grundfos Holding A/S
DK-8850 Bjerringbro

P

1

(W) MPa

Min.
Max.

X.XX
X.XX

XX

XXX

X.X

EEI≤ 0.XX - Part X

XXXV ~ XX/XXHz IPXXX TFXXX

P/N:XXXXXXXX      
S/N:XXXXXXXX
Made in XXXXXXX

P

L.avg.

<XXW

Denmark

2

3

4

5
6

8

7

9

10

23

22

21

20

19
18
17

16

14

15

11

12

13

Min.XX°C

Model:XXXXXX X

GFNXX

PC:P1XXXX

1

TM0769471

Nameplate

Pos.

Description

1

Pump name

2

Minimum current [A]

3

Maximum current [A]

4

CE mark and approvals

5

Energy Efficiency Index, EEI

6

Voltage [V]

7

Average power input PL, avg (Ecodesign regulation)

8

Model designation

9

Product number

10

Serial number

11

Country of origin

12

Frequency [Hz]

13

Part, according to EEI

14

Enclosure class

15

Manufacturer’s name and address

16

Production code:

1st and 2nd figures: production site code

3rd and 4th figures: year

5th and 6th figures: week

17

Minimum liquid temperature

18

Product mark (legal product code)

19

TF class

20

Crossed-out wheeled bin according to EN 50419

21

Maximum system pressure [MPa]

22

Maximum input power [W]

23

Minimum input power [W]

2.3.2 Type key, ALPHA SOLAR

Example: 

ALPHA SOLAR 15 - 75 130

Code

Explanation

ALPHA SOLAR

Pump type

15

Nominal diameter (DN) of inlet and outlet
ports [mm]

75

Maximum head [MPa]

-

[ ]: Cast-iron pump housing
N: Stainless-steel pump housing

130

Port-to-port length [mm]

3. Receiving the product

3.1 Inspecting the product

CAUTION
Crushing of feet

Minor or moderate personal injury

Wear safety shoes when opening the box and handling
the product.

On receipt of the product, do the following:
1.

Check that the product is as ordered.
If the product is not as ordered, contact the supplier.

2.

Make sure that the supply voltage and frequency correspond to
the values stated on the product nameplate.

Related information

2.3.1 Nameplate, ALPHA SOLAR

3.2 Scope of delivery

The box contains the following items:

ALPHA SOLAR pump

Superseal power cable

Mini superseal signal cable

two gaskets

quick guide.

4. Installation requirements

DANGER
Electric shock

Death or serious personal injury

Switch off the power supply before you start any work
on the product. Make sure that the power supply
cannot be switched on accidentally.

CAUTION
Crushing of feet

Minor or moderate personal injury

Wear safety shoes when opening the box and handling
the product.

Installation must be carried out by trained persons in
accordance with local regulations.

The pump must always be installed with a horizontal
motor shaft within ± 5°.

7

English (GB)

Содержание ALPHA SOLAR B


























Отзывы: