VER. 003_20.05.2011
CONNECTION
MOUNTING, CONNECTION
APPLICATION
1. Disconnect power supply by the phase fuse, the circuit-
breaker or the switch-disconnector combined to the
proper circuit.
2. Check if there is no voltage on connection cables
by means of a special measure equipment.
3. Connect the cables with terminals in accordance with
the installing diagram.
4. Install RNP-01 device in installation cable box.
5. Switch on the power supply from the mains.
The device is ready to operate after correct mount-
ing and connection. Releasing the system by a mon-
ostable push-button connected to one of four release
terminals (IN1-IN4) causes the RNP-01 device to send
a radio control signal added to this input (channel).
LED red diode signals the transmission is on. Device
programming procedure (adding a transmitter to re-
ceiver’s memory) is described in manual instructions
of particular EXTA FREE receivers.
4-channel radio transmitter RNP-01
controls operation of radio flush dimmer
RDP-01 (switch on/switch or light bright-
ening/dimming) or remote control socket
RWG-01 (switch on/switch off). The re-
ceivers can be controlled by 8-channel
P-256/8 remote control. RNP-01 device
can be mounted under the existing light-
ing switch (required power supply: 230V
AC – L and N wires).
COOPERATION AND OPERATING RANGE
Symbol:
ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTI-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
*- 1-channel transmitters do not cooperate with roller blind controllers.
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: wood and plaster - from 5 to 20, bricks - from 10 to 40 %, reinforced concrete - from 40 to 80 %, metal - from 90 to 100%,
glass - from 10 to 20 %. Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system
have also a negative influence on the range.
The ZAMEL company devices
which are characterised with
this sign can cooperate with
each other.
GRUBER Electric Ges.m.b.H
.
A-1230 Wien, Eduard Kittenberger Gasse 97 Top 2
Tel. +43 1 8692339 / Fax +43 1 8651875
Internet: www.gruber-electric.at E-Mail: [email protected]
Komponenten für Steuerungsbau und Industrieelektronik
