Grohe Sentosa 19 696, Руководство пользователя

Страница: 4 / 12

1
English
Installation to finished stage
- Plaster and tile the wall, excluding the area occupied by the
mounting template. Seal any apertures in the wall so that they
are watertight to spray water.
•
Tiles laid in mortar should be pointed so that the joint is
tapered towards the outside.
•
Seal prefabricated walls with a permanently plastic compound.
- Remove the mounting template, see fig. [1].
- Install holder (U), screw-mount sleeve (H) and sleeve (R), see
fig. [2].
- Grease the seals (T) of the escutcheon (K) with the special
grease supplied and install escutcheon (K) with screws (L), see
fig. [3].
- Fit the cap (O), see fig. [3].
If the thermostat has been installed at too great a depth, this
can be adjusted by 1 1/8" (27.5mm) with an extension set (see fold-
out page II and III, ref. No. 47 358).
Installation of the flow control knob and adjustment of the
economy stop, see figs. [4] to [6].
•
The flow rate is limited by the economy stop (N) supplied, see
fig. [4].
To install the flow control knob, proceed as follows:
1. Close the ceramic headpart by turning clockwise.
2. Install the economy stop (N) in the desired position, see fig. [4].
For possible settings, see fig. [5].
3. Reinstall splined adapter (J) and shut-off knob (I) with economy
button (V) pointing to the right.
Reinstall screw (P) and refit cap (G), see fig. [6].
If a higher rate is desired, the stop can be overridden by depressing
the flow control knob (V), see fig. [6].
Adjustment
Installation of the thermostat knob and temperature
adjustment, see figs. [7] and [8].
•
Before the mixer is put into service if the mixed water
temperature measured at the point of discharge varies from the
specified temperature set on the thermostat.
•
After any maintenance operation on the thermoelement.
1. Open the shutt-off valve and check the temperature of the water
with a thermometer, see fig. [7].
2. Turn the adjusting nut (A) clockwise or anticlockwise until the
water temperature reaches 100
°
F, see fig. [7].
3. Reinstall the thermostat knob (C) in such a way that the 100
°
F
mark on the knob coincides with the mark (S) on the cap (O).
4. Reinstall screw (D) and refit cap (M), see fig. [8].
Reversed union (hot on right - cold on left).
Replace thermoelement (F), see replacement parts fold-out page II
and III, ref. No.: 47 282 (1/2”).
Temperature limitation
The safety stop limits the temperature range to 100
°
F.
If a higher temperature is desired, the 100
°
F limit can be
overridden by depressing the temperature control handle.
Prevention of frost damage
When the domestic water system is drained, thermostat mixers
must be drained separately, since non-return valves are installed in
the hot and cold water connections.
The complete thermostat assemblies and non-return valves must
be unscrewed and removed.
Maintenance
For maintenance, see fig. [9] and fold-out page II and III.
Shut off hot and cold water supplies.
I. Thermoelement
1. Lever out cap (M).
2. Unscrew and remove (D) and pull off thermostat knob (C).
3. Unscrew and remove adjusting nut (A).
4. Pull off stop ring (B).
5. With a 15/16" (24mm), open-ended spanner, unscrew and
remove thermoelement (F).
II. Non-return valve
1. Lever out cap (M) and (G).
2. Unscrew and remove screws (D) and (P), pull off thermostat
knob (C) and shut-off knob (I).
3. Detach cap (O) in accordance with fig. [9].
4. Remove screws (L) and escutcheon (K).
5. Unscrew and remove non-return valve (E) with 11/16" (17mm)
open-ended spanner or 3/8" (10mm) allen key.
III.Ceramic headpart
1. Proceed as for maintenance of non-return valve, points 1-4.
2. Remove splined adapter (J) and economy stop (N).
3. Remove sleeve (H) and holder (U).
4. With a 11/16" (17mm) open-ended spanner, unscrew and
remove ceramic headpart (W).
Inspect and clean all parts, replace if necessary and grease with
special valve grease (ref. No. 18 012).
Reassemble in the reverse order.
Observe the correct mounting position!
Use only genuine Grohe replacement parts.
Replacement parts, see fold-out page II and III (* = special
accessories).
Readjustment is necessary after every maintenance operation on
the thermoelement (see Adjustment).
Care
For directions on the care of this thermostat mixer, please refer to
the accompanying Care Instructions.
951021.book : I95102us.fm Seite 1 Donnerstag, November 30, 2000 4:03 PM