Grohe Blue Professional 31 607, Руководство пользователя

Страница: 22 / 32

Use only original spare parts and accessories . The use of other
parts will result in voiding the warranty and the CE marking, and
could cause injury.
The filter head
must be replaced after 5 years.
Technical data cooler/carbonator electrical data:
• Connection: Wall socket with earth wire,
protected via a 10
A
fuse
• Voltage supply: 230 V
A
C / 50 Hz
• Max. power consumption: 240 W
• Type of protection: IP 21
• Relative air humidity: max. 80%
• Refrigerant: 0.030 kg - R600a
• Safety shut-off of pump: approx. 4:30 min
• Operating pressure: min. 0,2 MPa - max. 1 MPa
• Max. CO
2
inlet pressure: 0.5 MPa
• Max. refrigerant pressure: 3.0 MPa
• Temperature class: N
Sanitary data:
• Cooler/carbonator cooled water capacity: 1.4 l
• Operating pressure: max. 0.55 MPa
• Flow rate at 0.3 MPa flow pressure: approx. 2 l/min
•
Am
bient temperature:
4
– 35 °C
• Temperature
– Cooler/carbonator water inlet: max. 24 °C
– Cooled water temperature: approx. 5 – 10 °C
• Sound pressure level Lp
A
(frestanding): 50 ± 4 dB
• Adjustable bypass, factory setting: 2
• Filter capacity Bypass Position 2
(Carbonate hardness 17 - 24 °KH): max. 3000 litres
corresponds to max. 6 months
• Water connection
– Cooler/carbonator: cold - blue
Electrical test data:
• Software class:
A
• Contamination class: 2
• Rated surge voltage: 2,500 V
The test for electromagnetic compatibility (interference emission
test) was performed at the rated voltage and rated current.
Technical data fitting:
• Flow pressure: 0.2 – 0.9 MPa
• Operating pressure: max. 1 MPa
• Test pressure: 1.6 MPa
To comply with noise levels if static pressure exceeds 5 bar, a
pressure reducing valve must be fitted.
Avo
id major pressure differences between hot and cold water
supply.
• Flow rate at 3 bar flow pressure: approx. 9 l/min
• Temperature
– Hot water inlet: max. 70 °C
– Recommended (energy saving): 60 °C
Water connection: cold - right
hot - left
Thermical disinfektion of the fitting is possible.
Installation and commissioning
GROHE recommends a depth of min. 500 mm for
the cabinet.
Flush pipes thoroughly before and after installation
(observe EN 806) !
Adjust bypass of filterhead according to local carbonate
hardness and connect filter cartridge.
The carbonate hardness can be tested by using the enclosed test
strip or the relevant water supplier can provide information on the
carbonate hardness.
The fitting has a system-related run-on time of approx. 1 s.
Note: Make sure that the water inlet hose does not come loose
by movement when installing the cooler.
When transporting or installing the cooler/carbonator,
cooling fluid may have run into the lines.
In order to ensure that the cooling fluid has run back, the
cooler/carbonator may only be installed following a pause
of 24 hours.
Display:
In the inactive state, the remaining filter capacity is displayed in per
cent.
When carbonate hardness ≤9° the use of activated carbon
filter (Order no.: 40 547 001) is recommended.
The cooler/carbonator of the GROHE Blue® fitting is set for
operation with the UltraSafe filter cartridge (Prod no.: 40 575 001)
at the factory.
For operation with other filter cartridges the cooler/carbonator must
be set out.
Maintenance and cleaning
CAUTION!
Risk of damage!
Always disconnect the power supply and interrupt the CO
2
supply before carrying out maintenance work on the
system. The plug-in connector can then be disconnected.
Cleaning the cooler/carbonator
For hygienic and health reasons, the cooler/carbonator must be
cleaned twice a year. Cleaning must be performed before
changing the filter cartridge, in order to prevent contamination
of the replacement filter cartridge.
Note: The cleaning kit (Prod. no.: 40 434 001) and the
accompanying adapter (Prod. no.: 40 694 000) can be ordered at
www.shop.grohe.com
21