background image

OM-TDB TA/2

3

IMPORTANT — READ FIRST — IMPORTANT

WARNING:

THE UNIT IS EQUIPPED WITH AN AUTOMATIC CUTOFF SWITCH.  IF POWER IS ON WHEN A
TILTED  MIXER  IS  LOWERED  INTO  THE  OPERATING  POSITION,  THE  MIXER  WILL
AUTOMATICALLY START.

CAUTION:

STARTING WITH THE MIXER SET AT HIGH SPEED MAY CAUSE MATERIAL TO SPILL OUT
OF THE KETTLE ON TWO SPEED AND VARIABLE SPEED UNITS.

CAUTION:

UNDER HEAVY LOAD DO NOT RUN THE MIXER CONTINUOUSLY AT SLOWER THAN 5% OF
FULL SPEED.  SLOWER OPERATION COULD DAMAGE THE SPEED CONTROL.

WARNING:

BEFORE  CLEANING  ANY  PART  OF  THE  MIXER,  OTHER  THAN  THE  AGITATOR,
DISCONNECT  THE  ELECTRICAL  SUPPLY  AT  THE  CIRCUIT  BREAKER  OR  FUSE  BOX  TO
AVOID POSSIBLE ELECTRICAL SHOCK.

WARNING:

KEEP  WATER  AND  SOLUTIONS  OUT  OF  THE  CONTROLS,  ELECTRICAL  WIRING,  AND
DRIVE MECHANISM.  NEVER SPRAY OR HOSE THE MIXER.

CAUTION:

WHEN  YOU  CONNECT  THE  SCRAPER  WITH  THE  YOKE,  MAKE  SURE  THE  SCRAPER  IS
CURVED  THE  SAME  WAY  AS  THE  KETTLE.    A  REVERSED  SCRAPER  WILL  NOT  SCRAPE
AND CAN CAUSE SERIOUS DAMAGE.

WARNING:

AVOID  CONTACT  WITH  CLEANING  PRODUCTS  IN  ACCORDANCE  WITH  SUPPLIER  AND
MANUFACTURER RECOMMENDATIONS.  MANY CLEANERS ARE HARMFUL TO THE SKIN,
EYES,  MUCOUS  MEMBRANES  AND  CLOTHING.    READ  THE  WARNINGS  AND  FOLLOW
DIRECTIONS ON THE CLEANER LABEL.

WARNING:

USE  OF  ANY  REPLACEMENT  PARTS  OTHER  THAN  THOSE  SUPPLIED  BY  GROEN  OR
THEIR  AUTHORIZED  DISTRIBUTOR  VOIDS  ALL  WARRANTIES  AND  CAN  CAUSE  BODILY
INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT.

WARNING:

SERVICE PERFORMED BY OTHER THAN FACTORY AUTHORIZED PERSONNEL WITH VOID
ALL WARRANTIES.

WARNING:

BEFORE  REPLACING  ANY  PARTS,  SHUT  OFF  ALL  ELECTRIC  POWER  SUPPLIES  TO  THE
COOKER/MIXER.

WARNING:

USE  ONLY  GROEN-SUPPLIED  PARTS.    SUBSTITUTION  OF  UNAUTHORIZED  OR  GENERIC
PARTS  CAN  RESULT  IN  BODILY  INJURY  TO  THE  OPERATOR  AND  DAMAGE  TO  THE
EQUIPMENT.

Содержание TDB-20 TA/2















Отзывы: