OM/SM-HY-6E(CE)
OM/SM-HY-6E(CE)
28
5. The hose may be removed. Be careful that the hose
clamps do not fall off and get lost.
IMPORTANT:
Make sure that the correct part (and
part number) are being used. The two hoses in the
steamer are of different lengths. (See Page 17 for
Part Numbers.)
To Install:
6. Slide the two hose clamps onto the hose and position
the hose adjacent to the steam port and steam
generator.
7. Slide the hose onto the hose nipple on the steam port
and at the other end, onto the steam generator
nipple. Make sure the hose is on all the way so that
the end of the hose is against the face of the nipples.
8. Install the hose clamps 5/64" (2 mm) from the end of
the hose.
10.23
Door Removal/Installation/Alignment
P/N 094150
1. To remove the door, turn off the steamer power and
allow the steamer to cool. Then, remove door by
supporting the weight of the door and remove hinge
pin.
2. Place the door on a flat, clean table or similar
support, with gasket facing up.
Be careful not to
scratch door surface.
3.
Inspect door gasket for signs of cuts or other defects
which may impair its function. Replace if necessary.
To Install:
4. To install the door, apply NEVER-SEEZ lubricant to
hinge pin. Align door with hinge and insert hinge pin,
or apply Locktite 242 to the door-to-hinge bolts, then
install door and mounting bolts. Do NOT tighten
mounting bolts at this time.
To Align:
5. Place a piece of masking tape over the door pin
(bullet) hole in the door.
6. Close the door until the door pin just penetrates the
masking tape. Make sure the door pin contacts only
the door latch spring.
7. If door pin does not strike the center of the masking
tape or spring hole in the U-channel, loosen the
hinge-to-oven bolts and align the door to the door pin.
Tighten hinge-to-oven mounting bolts.
8. You should be able to pull a dollar bill or comparable
piece of paper smoothly between the gasket and oven
cavity with the door closed. To adjust the hinge side,
loosen the door-to-hinge bolts and align the door
gasket with the oven cavity. Tighten the door-to-hinge
mounting bolts. To adjust the bullet side refer to 10.29.
9. Operate oven in steam mode and check for leaks.
10.24
Door Switch
P/N 096857
1. From the right side of the steamer with panel
removed, unplug the door switch from the cable
harness.
2. The switch (for normal door opening) is held in place
with two small 4-40 screws. With a flat blade
screwdriver, remove these screws and the switch may
be removed.
3. To install 4-40 screws for the door switch use a screw
starter.
4. If the door has been reversed and the switch must be
removed and replaced, refer to the top and left side
panel removal in Section 10.3 and then remove the
switch as above.
10.25
Door Reversing Procedures
1. Turn off steamer power and allow steamer to cool.
2. To remove door, support door while removing hinge-
to-steamer bolts.
3. Place door with hinge on a flat, clean table (or similar
support), with the gasket facing
up. Be careful not to
scratch door surface.
4. Note and record distance between lock nut and end of
door locking pin (bullet). This information will be
needed during bullet installation described in Step 6.
5. Loosen lock nut with a wrench. Remove door locking
pin and lock nut.
6. Coat
bullet
threads with NEVER-SEEZ high
temperature compound. Install door locking pin and
lock nut directly across steamer cavity from old door
locking pin location. Install these items so that lock
nut-to-end of bullet distance is approximately the
same as measured in Step 4.
7. Remove the two 1/4-20 truss head screws from above
and below the old bullet location and install them
above and below the new bullet location.