background image

6 OM-INA/2

Initial Start-Up

WARNING

TURN OFF AGITATOR BEFORE ADDING

INGREDIENTS OR INSPECTING KETTLE

CONTENTS. DO NOT WEAR LOOSE

CLOTHING OR JEWELRY AROUND

OPERATING MIXER KETTLE. KEEP WELL
CLEAR OF ROTATING MIXER ARMS AND

PADDLES AT ALL TIMES.

After the mixer is installed, take the following actions to confirm that the equipment is

operating correctly.

1.  Tilt the mixer through its complete tilting range to ensure that there is no hazard or 

interference.

2.  Make sure the agitator is properly coupled with its drive shaft. If the mixer has 

a slip-on coupling, the drive pin must be positioned at the end of the J-slot. If a 

bolted coupling is employed, the bolts must be turned to the proper position and 

the nuts must be tightened.

3.  When the mixer is in operating position, every scraper blade should touch the 

inside of the kettle during at least part of each revolution of the agitator.

4.  At the circuit breaker or fuse box, turn on the electric power supply to the mixer.

5.  Switch on the drive and confirm that the mixer operates smoothly. For a variable 

speed model, confirm that the mixer operates correctly throughout its speed range.

6.  Make sure the agitator turns in the correct direction, so it pushes the nylon scraper 

blades ahead of the agitator bar.

If the unit functions as described above, it is ready for use. If the unit does not function 

as intended, call your local Groen authorized service agency.

For instructions on initial start-up of the kettle component of your cooker/mixer, see 

the separate kettle manual.

Slip-On Coupling

Agitator Operation

TO RUN AGITATOR

1.  Ensure kettle is fully upright.

2.  Ensure mixer head is fully down and latched.

3.  Set the speed dial to desired speed.

4.  Turn the start switch to ON.

TO STOP AGITATOR

1.  Press the red STOP button or turn the ON/OFF toggle switch to OFF.

WARNING

DO NOT PLACE HANDS, TOOLS, OR HOSES 

IN KETTLE WHILE AGITATOR IS MOVING. 

AGITATOR AREA MUST BE CLEAR OF 

OBSTRUCTION BEFORE OPERATION.

Kettles with 100 Gallon capacity and larger

Содержание D - 40/60/80 INA/2

















Отзывы: