background image

Model h7668 spray gun w/pressure Cup

-15

-

section 6: maintenance

cleaning

proper cleaning is the best way to ensure 
trouble  free  performance  from  your  spray 
system.  if  your  system  is  not  thoroughly 
cleaned,  damage  and  poor  spraying  will 
result. problems caused by improper clean-
ing  will  not  be  covered  by  the  warranty. 
Clean  the  spray  gun,  hose  and  pressure 
cup immediately after each use.

to clean your spray system:

1.   depressurize the cup by disconnecting 

from  the  compressed  air  and  bleed 
the  system  by  loosening  (do  not 
rEMoVE)  the  pressure  relief  valve 
until "zero" pressure is recorded on the 
pressure cup gauge (see 

figure 20).

eXplosion  hazard!  chlorinated 
solvents  like  1,1,1-tricloroethane 
and  methylene  chloride  (methyl 
chloride)  can  chemically  react  with 
aluminum  and  may  explode.  many 
parts  in  spray  guns  and  pressure 
cups  are  made  of  aluminum.  read 
your  solvent  label  carefully  before 
using solvent.

eXplosion  hazard!  do  not 
unscrew  pressure  cup  lid  while 
under  pressure!  exploding  paint 
material  and  solvents  could  cause 
serious injury!

3.  Clean pressure cup with solvent.

4.   add  clean  solvent  to  pressure  cup, 

replace the lid and repressurize.

5.  spray  the  gun  until  the  fluid  sprays 

clear to clean the fluid hose.

 

note:  Check  local  laws  regarding  this 
practice. If you are spraying on a regu-
lar basis, spraying solvents into the air 
may be illegal. A closed system cleaner 
may be required.

health 

contamination 

hazard!  dispose  of  paint  waste 
in  a  responsible  manner!  follow 
manufacturer's  recommendations 
and  local  laws  regarding  disposal. 
failure  to  comply  will  result  in  con-
tamination  and  possibly  large  fines 
and penalties.

2.   unscrew the cap and empty the pres-

sure  cup  contents  into  an  approved 
receptacle. 

figure 20. pressure relief valve.

pressure relief Valve

Содержание H7668

























Отзывы: