Grizzly G0894 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

background image

Model G0894 (Mfd. Since 05/19)

-23-

SECTION 4: OPERATIONS

To complete a typical operation, the operator

does the following:

1. Designs/writes G-code that defines toolpath.

2. Uploads G-code to USB drive.

3. Examines workpiece to make sure it is suit-

able for cutting.

4. Installs appropriate cutter for type of material

and operation.

5. If necessary, cuts workpiece to fit within

working envelope of machine.

6. Clamps workpiece securely to table.

7. Turns machine ON.

8. Homes all axes and verifies parameters (see

Page 22).

9. Connects USB drive to hand-held controller.

10. Sets work origin. Sets Z-axis relative to

workpiece or table, depending on toolpath
requirements.

11. Connects dust shoe and dust collection sys-

tem to spindle.

12. Puts on safety glasses, respirator, and hear-

ing protection.

13. Plugs in cooling pump and turns dust collec-

tion system

ON

13. Runs G-code. Spindle will automatically start

and follow toolpath.

14. When toolpath is complete, spindle will stop

and return to position defined by G-code.

Operation Overview

The purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.

Due to the generic nature of this overview, it is

not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual, seek additional training from experienced
machine operators, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

If you are not experienced with this type

of machine, WE STRONGLY RECOMMEND

that you seek additional training outside of

this manual. Read books/magazines or get

formal training before beginning any proj-

ects. Regardless of the content in this sec-

tion, Grizzly Industrial will not be held liable

for accidents caused by lack of training.

Eye injuries, respiratory problems, or hear-

ing loss can occur while operating this

tool. Wear personal protective equipment to

reduce your risk from these hazards.

«
...
23
24
25
26
27
...
»

Содержание G0894

















































Отзывы:

Нет отзывов

Похожие инструкции для G0894

Бренд: Parkside Страницы: 78

Бренд: IVT Страницы: 40

Бренд: Milwaukee Страницы: 9

Бренд: Power Adhesives Страницы: 16

Бренд: Magswitch Страницы: 2

Бренд: M7 Страницы: 17

Painting machine

Бренд: Valex Страницы: 20

XPower Powerpack 300

Бренд: Xantrex Страницы: 60

Бренд: MATO Страницы: 17

Бренд: Whelen Engineering Company Страницы: 2

Flatscreen PowerProtect 200

Бренд: Monster Страницы: 2

Бренд: Eastwood Страницы: 4

Бренд: NovoPress Страницы: 46

Бренд: Paxton Страницы: 3

Бренд: Hamach Страницы: 24

Бренд: HOZAN Страницы: 16

NEW PACER 100 Series

Бренд: Wolf Страницы: 40

Бренд: Rehau Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды