manualshive.com logo in svg

Grizzly G0779, Руководство пользователя

Поделиться
Скачать
Grizzly G0779 Скачать руководство пользователя страница 19

Model G0779 (Mfd. Since 09/14)

-17-

GEARBOX MUST

BE FILLED WITH OIL!

OIL MAY NOT BE

SHIPPED WITH MACHINE!

Refer to Lubrication Section

for Correct Oil Type.

Initial Lubrication

To  prevent  spillage,  this  machine  was  shipped 
from  the  factory  without  any  oil  in  it.  The  head-
stock oil reservoir must be properly filled with oil 
before the drill press can be operated for the first 
time. Refer to the 

Lubrication section, beginning 

on 

Page 31, for details on how to check and add 

oil.

Arbor/Chuck 

Assembly

Damage caused by running the drill press 

without oil in the reservoir will not be cov-

ered under warranty. 

An  arbor  is  included  for  the  drill  chuck  that 
comes with this machine. The following procedure 
describes how to install the arbor in the chuck.

After  the  arbor  is  installed  in  the  drill  chuck,  it 
is  very  difficult  to  separate  the  assembly.  If  you 
would  like  to  use  a  different  chuck  in  the  future, 
we recommend obtaining a new arbor.

IMPORTANT: DO NOT  install  the  drill  chuck 
and arbor assembly into the spindle until 

AFTER 

the test run.

To join drill chuck and arbor:

1.  Use acetone or lacquer thinner to clean drill 

chuck and arbor mating surfaces, especially 
the bore.

2.  Retract chuck jaws completely into chuck.

3.  Insert small end of arbor into chuck.

4.  Hold  assembly  by  the  arbor  and  tap  chuck 

onto a block of wood with medium force, as 
illustrated below.

5.  Attempt to separate drill chuck and arbor by 

hand —if they separate, repeat 

Steps 3–4.

Figure 10. Arbor/chuck assembly.

Содержание G0779





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды