Grizzly G0677 Скачать руководство пользователя | Manualshive

Страница: 35 / 96

background image

G0677 24" Planer/Sander

-33-

Workpiece

Inspection

Some workpieces are not safe or may require
modification before they are safe to plane or
sand.

Before planing or sanding, inspect all

workpieces for the following:

•

Material Type: This machine is intended for
ONLY  cutting  natural  and  man-made  wood
products.  This  machine  is  NOT  designed  to
plane or sand metal, glass, stone, tile, drywall
or  cementitious  backerboard,  laminate  cov-
ered wood products or plastics; cutting these
materials with this planer/sander may lead to
injury.

•

Foreign Objects:  Nails,  staples,  dirt,  rocks
and  other  foreign  objects  are  often  embed-
ded  in  wood.  While  planing,  these  objects
can  become  dislodged  and  hit  the  operator,
cause  kickback,  break  the  inserts,  or  tear
the  sanding  belt.  Always  visually  inspect
your workpiece for these items. If they can't
be  removed,  DO  NOT  plane  or  sand  the
workpiece.

•

Wet or "Green" Stock: Cutting wood with a
moisture content over 20% causes unneces-
sary wear on the inserts, increases the risk of
kickback, and yields poor results.

•

Excessive Warping: Workpieces with exces-
sive cupping, bowing, or twisting are danger-
ous to plane because they are unstable and
often unpredictable when being cut. DO NOT
use workpieces with these characteristics!

•

Minor Warping: Workpieces with slight cup-
ping  can  be  safely  supported  if  the  cupped
side  is  facing  the  table.  On  the  contrary,  a
workpiece supported on the bowed side will
rock  and  could  cause  kickback  or  severe
injury.

«
...
33
34
35
36
37
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: Teac Страницы: 16

Бренд: Lasonic Страницы: 7

Бренд: Emerson Страницы: 24

Бренд: Makita Страницы: 64

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды