Grizzly G0677 Скачать руководство пользователя

Страница: 26 / 96

-24-

G0677 24" Planer/Sander

Damage to your eyes, lungs, and ears could

result from using this machine without

proper protective gear. Always wear safety

glasses, a respirator, and hearing protection

when operating this machine.

SECTION 4: OPERATIONS

NOTICE

If you have never used this type of machine

or equipment before, WE STRONGLY REC-

OMMEND that you read books, trade maga-

zines, or get formal training before begin-

ning any projects. Regardless of the con-

tent in this section, Grizzly Industrial will

not be held liable for accidents caused by

lack of training.

To reduce the risk of

serious injury when using

this machine, read and

understand this entire

manual before beginning

any operations.

Loose hair, clothing, or

jewelry could get caught

in machinery and cause

serious personal injury.

Keep these items away

from moving parts at all

times to reduce this risk.

Basic Controls

Refer to

Figures 25–28 and the descriptions

below to become familiar with the basic controls
and components of your planer/sander.

Control Panel

Amp Load Meter: Indicates the current amp load
on the main motor when a planing and sanding
operation is in progress.

Sanding Belt Start and Stop Buttons: Turns the
sanding motor

ON and OFF if the planer/sander

has air pressure, the belt is tensioned, the power
is connected, and all access doors are closed and
locked.

Feed Belt Start and Stop Buttons: Cycles the
feed belt motor

ON and OFF for feeding wood into

the planer/sander.

Figure 25. Control panel.

Amp Load

Meter

Feed

Belt Stop

Button

Power

Light

Front Stop

Button

Feed

Belt Start

Button

Sanding

Belt Stop

Button

Sanding

Belt Start

Button

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды