Grizzly G0561 Скачать руководство пользователя страница 42

Страница: 42 / 60

-40-

Model G0561 (Mfd. Since 01/08)

Review the troubleshooting and procedures in this section if a problem develops with your machine. If
you need replacement parts or additional help with a procedure, call our Technical Support.

Note: Please

gather the serial number and manufacture date of your machine before calling.

SECTION 7: SERVICE

Troubleshooting

Motor & Electrical

Symptom

Possible Cause

Possible Solution

Machine does not start
or a breaker trips.

1. Plug/receptacle is at fault/ wired incorrectly.
2. Power supply is at fault/switched OFF.

3.  Motor wired incorrectly.
4.  Start capacitor is at fault.
5.  Wall fuse/circuit breaker is blown/tripped.

6. Motor ON/OFF switch is at fault.
7. Wiring open/has high resistance.

8. Motor is at fault.

1. Test for good contacts; correct wiring.
2. Ensure hot lines have correct voltage on all

legs and main power supply is switched ON.

3.  Correct motor wiring.
4.  Test/replace.
5.  Ensure correct size for machine load; replace

weak breaker.

6. Replace faulty ON/OFF switch.
7. Check/fix broken, disconnected, or corroded

wires.

8. Test/repair/replace.

Machine stalls or is
underpowered.

1. Wrong blade for workpiece material.

2. Wrong workpiece material.

3.  Feed rate/cutting speed too fast for task.
4.  Blade is slipping on wheels.
5.  Low power supply voltage.

6. Motor bearings are at fault.

7.  Plug/receptacle is at fault.
8.  Motor connection is wired incorrectly.
9.  Motor has overheated.

10. Motor is at fault.

1. Use blade with correct properties for your type

of cutting.

2. Use metal with correct properties for your type

of cutting.

3.  Decrease feed rate/cutting speed.
4.  Adjust blade tracking and tension.
5.  Ensure hot lines have correct voltage on both

legs.

6. Test by rotating shaft; rotational grinding/loose

shaft requires bearing replacement.

7.  Test for good contacts; correct the wiring.
8.  Correct motor wiring connections.
9.  Clean off motor, let cool, and reduce

workload.

10. Test/repair/replace.

Machine has vibration
or noisy operation.

1. Motor fan is rubbing on fan cover.

2.  Blade is at fault.
3.  Gearbox is at fault.
4.  Wrong blade and/or speed too slow.

1. Replace dented fan cover; replace loose/

damaged fan.

2.  Replace/resharpen blade.
3.  Rebuild gearbox for bad gear(s)/bearing(s).
4.  Change blade and/or speed.

Содержание G0561





























































Результаты поиска

Содержание G0561

Отзывы:

Похожие инструкции для G0561

Бренды по названию

Популярные бренды

Grizzly G0561, Руководство пользователя

Результаты поиска

Содержание G0561

Отзывы:

Похожие инструкции для G0561

Бренды по названию

Популярные бренды