"')"
<%***AM
B[\#H^cXZ%&$&'
I]Z YZ[aZXi^dc bZi]dY ^h bjX] bdgZ hjW_ZXi^kZ
i]Vc i]Z [ajiiZg bZi]dY# :VX] WaVYZ l^aa YZ[aZXi
Y^[[ZgZcian VcY ZkZgn jhZg l^aa YZiZgb^cZ l]Vi
bdYZgViZ egZhhjgZ bZVch# I]Z [daadl^c\ VgZ
\ZcZgVa \j^YZa^cZh [dg iZch^dc^c\ i]Z WaVYZ l^i]
i]^hbZi]dY#
To tension the bandsaw blade:
1.
9>H8DCC:8I76C9H6L;GDBEDL:G#
2.
BV`Z hjgZ i]Z WaVYZ ^h egdeZgan igVX`^c\ Vh
^chigjXiZY^ci]Z
Blade Tracking
hjWhZXi^dc
dc
Page 19
#
3.
GV^hZ i]Z \j^YZ edhi Vaa i]Z lVn VcY bdkZ
i]Z jeeZg VcY adlZg \j^YZ WZVg^c\h VlVn
[gdbi]ZWaVYZ#
4.
:c\V\Zi]ZWaVYZiZch^dcfj^X`gZaZVhZaZkZg
idVeeaniZch^dcidi]ZWaVYZ#
5.
Jh^c\bdYZgViZegZhhjgZ!ejh]i]ZXZciZgd[
i]ZWaVYZh^YZlVnh#
·>[i]ZWaVYZYZ[aZXihVeegdm^bViZan
&
¿
)
^i^h
egdeZganiZch^dcZY#EgdXZZYid
Step 7
#
·>[i]ZWaVYZYZ[aZXihaZhhi]Vc
&
¿
)
^i^hdkZg"
iZch^dcZY#Ijgci]ZWaVYZiZch^dc^c\`cdW
XdjciZgXadX`l^hZild[jaaijgchVcYgZeZVi
Step 6
#
·>[i]ZWaVYZYZ[aZXih
&
¿
)
dgbdgZ!i]ZWaVYZ
^hcdiegdeZganiZch^dcZY#6eeaniZch^dcid
i]ZWaVYZ^cXgZbZciVaanVcYgZeZVi
Step 6
jci^aegdeZganiZch^dcZY#
6.
GZ"VY_jhi WaVYZ \j^YZh Vh YZhXg^WZY ^c
Adjusting Blade Support Bearings
VcY
Adjusting Blade Guide Bearings
dc
Pages
25– 26
#
When using different size blades, the blade
tensioning system may need to be reset for
correct operation. Refer to
Blade Tensioner
on
Page 52
for detailed instructions.
Note:
Tensioning the blade according to the
blade tension scale before the
Test Run
was an
approximate tension. The following procedures
fine-tunes the blade tension.
1.
9>H8DCC:8I76C9H6L;GDBEDL:G#
2.
BV`ZhjgZi]ZWaVYZ^hegdeZganXZciZgigVX`"
^c\Vh^chigjXiZY^ci]Z
Blade Tracking
hjW"
hZXi^dcegZk^djhdc
Page 19
#
3.
GV^hZ i]Z \j^YZ edhi Vaa i]Z lVn VcY bdkZ
i]Z jeeZg VcY adlZg \j^YZ WZVg^c\h VlVn
[gdbi]ZWaVYZ#
4.
:c\V\Zi]ZWaVYZiZch^dcfj^X`gZaZVhZaZkZg
idVeeaniZch^dcidi]ZWaVYZ#
10.
GZ"VY_jhi WaVYZ \j^YZh Vh YZhXg^WZY ^c
Adjusting Blade Support Bearings
VcY
Adjusting Blade Guide Bearings
dc
Pages 25– 26
#
9.
9^hXdccZXii]ZWVcYhVl[gdbedlZg#
5.
8dccZXii]ZWVcYhVlidedlZg!VcYijgci]Z
WVcYhVl
ON
#
6 .
Jh^c\ i]Z WaVYZ iZch^dc VY_jhibZci `cdW!
hadlan YZXgZVhZ WaVYZ iZch^dc jci^a ndj hZZ
i]ZWaVYZhiVgiid[ajiiZg#
7
# Hadlan ^cXgZVhZ i]Z iZch^dc jci^a i]Z WaVYZ
hideh[ajiiZg^c\!i]Zci^\]iZci]ZWaVYZiZch^dc
VY_jhibZci `cdW VcY VYY^i^dcVa
&
¿
-
id
&
¿
)
d[ V
ijgc#
8.
Add` Vi l]Vi i]Z iZch^dc \Vj\Z gZVYh VcY
jhZi]ViVhV\j^YZ[dgiZch^dc^c\i]ViheZX^[^X
WaVYZ^ci]Z[jijgZ#
Note:
Do not rely on this setting for other
blades or for long periods of time because all
blades require specific tensioning and stretch
with use. If you notice a decrease in perfor-
mance at the setting repeat this procedure.
With extended use, the blade tensioning sys-
tem may need to be reset. Refer to
Resetting
Blade Tensioner
in the
Service
section in
this manual for details.
The Flutter Method
The Deflection Method