
COPYRIGHT © JUNE, 2008 BY GRIZZLY INDUSTRIAL, INC., REVISED APRIL, 2019 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL10789 PRINTED IN TAIWAN
The Model G0531B/G0566B is the same as the Model G0566, except it has a magnetic brake motor, resaw
fence, and square fence rail. Besides the instructions, data sheet, circuit requirements, parts, and wiring
diagram in this insert, the content in the Model G0566 owner's manual is the same for both machines.
Before operating your new machine, you MUST read and understand this insert and the entire Model G0566
manual to reduce the risk of injury from improper use or setup.
If you have any further questions about this manual insert or the differences between the Model
G0531B/G0566B and the Model G0566, contact our Technical Support at
(570) 546-9663 or email
Machine Inventory
MODEL G0531B/G0566B
21" BANDSAW
MANUAL INSERT
For Machines Mfd. Since 09/18
and Owner's Manual Revised 10/04
Figure 1. G0531B/G0566B inventory.
B
C
E
D
F
G
H
I
J
K
Box Contents (Figure 1)
Qty
A. Bandsaw (not shown) ................................. 1
B. Miter Gauge ................................................ 1
C. Fence.......................................................... 1
D. Resaw Fence ............................................. 1
E. Guide Post Handwheel............................... 1
F. Hex Wrenches 5, 6mm ..........................1 Ea
G. Open-End Wrenches 10/13, 17/19mm ..1 Ea
H. Lifting Rings ................................................ 2
I. Resaw Fence Lock Handle (Fence) ........... 1
J. Sliding Plate M8-1.25 (Fence) .................... 1
K. Flat Washer 8mm (Fence) ......................... 1
Tools Needed
Qty
Hex Wrenches 5, 6mm .................................1 Ea
Open-End Wrenches 10/13, 17/19mm .........1 Ea
To assemble machine:
1. Remove cap screw, knobs, and washers that
hold fence rail to table, then remove rail.
2. Flip rail over and re-install with fasteners
removed in
Step 1.
3. Install fence handle on fence.
Assembly
The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to
Needed for Setup and gather
all listed items. To ensure the assembly process
goes smoothly, first clean any parts that are cov-
ered or coated in heavy-duty rust preventative (if
applicable).
V2.04.19
Содержание g0531b
